Problem
I want to install one of SCO's operating system products on my
new computer. What basic advice could you give that will help
my installation go smoothly? Solution
Personal computer hardware configurations vary widely from manufac-
turer to manufacturer, so coming up with a specific recommendation
that will cover all machines is somewhat difficult. However, the
following guidelines when applied to a specific machine will help
your installation to go more smoothly:1. Through your system's CMOS setup program or hardware config- uration disk (such as an IBM or EISA setup disk), verify that the floppy disk configuration is correct. If you physically look at the machine and see that the A: drive is a 3.5" floppy drive and is connected to that wire set on the floppy disk controller card, it had better match that in your CMOS configuration.
2. Through your system's CMOS setup program or hardware config- uration disk, disable the system's shadow RAM, shadow BIOS, high speed cache.
3. Through your system's CMOS setup program or hardware config- uration disk, if possible, try to slow your machine down to avoid timing issues. Some PCs have jumpers on the motherboard for configuring speed. Consult your PC's hardware manual for details.
Many 486 and Pentium PCs have a slow mode that runs at 33Mhz or 66Mhz on the faster machines. This will ensure that your installation kernel can find all of your devices.
4. Disable any caching that you may have on your CPU and SCSI host adapter.
5. Put your SCSI host adapter in standard mode (not 32 bit).
6. Remove extraneous cards for devices that you do not need to install with such multiport boards, ethernet adapters, or fax cards.
7. Make sure you are using a supported video adapter with which to perform your installation.
If you have a non-supported VGA type, make sure autoswitching
is disabled (turn off Auto-switch from VGA to EGA mode). If
the video card is a 16 bit card, try putting it into an 8 bit
slot to avoid any DMA conflict.8. For SCSI host adaptors, make sure the terminating resistors are correctly seated and placed. Only the logical end of the chain of the SCSI bus is terminated. For the SCSI hard disks, make sure the target I.D. is jumpered correctly. By default, the installation kernel expects to find a hard drive at scsi id=0, tape drive at scsi id=2, cdrom drive at scsi id=5.
NOTE: Please refer to your hardware manual for information on configuring scsi target id numbers.
If you are <i>not</i> using a supported scsi host adaptor, or have your hardware devices configured at a scsi id other than where the default kernel expects to find the devices, then you <i>must</i> use a boot string to specify your configuration and/or link in your boot-time loadable driver (BTLD).
9. Check for different types of memory chips between the
motherboard and the add-on memory board. The chips ideally
should:a. have the same speed; b. have the same memory chip size.
For example, if the memory on the motherboard has 256K-size chips while the add-on board has 1Meg-size chips (for 4Meg RAM), then this may cause problems during installation.
10. Verify that the hard disk controller card is supported. A list
of supported hard disk controller cards is in the SCO System V
Operating System Release Notes or in the SCO Hardware Compat-
ibility Handbook.11. Put your 2.88 MB floppy drive in 1.44 mode.
12. If your hard disk has more that 1024 cylinders, then make sure
that you enable translation. Please refer to your hard disks
documentation for information on enabling translation mode.13. Disable additional CPU chips until after your installation is complete.
14. If you're planning on using a DOS, OS/2, Windows 95, or Windows NT partition, install it first.
When you have successfully completed your installation, you should:
1. Return your machine to its full speed.
2. Re-enable caching.3. If you are planning on having a bootable DOS partition then re-enable your shadow RAM.
4. Re-enable additional CPUs.If, after trying these things, you find that you are still having
trouble, most likely you either have incompatible hardware or you
may be in need of an installation supplement. You can verify the
hardware compatibility by checking the Release Notes or Hardware
Compatibility Handbook.When calling SCO Technical Support for assistance with installation problems, please be prepared to provide detailed information about your hardware configuration.