Technical article 107565

Get unknown arb command after configuring an IBM Token Ring adapter

OpenServer 5.0.0

Written · Last revised

Problem

This message appears on the console after configuring my IBM 16/4 ISA-16 Token Ring network adapter :

"Warning :tokintr (unit=<number>) unknown arb command <hex number>"
The network does not operate correctly.

Cause

One possible cause of this message is a conflict between the RAM and ROM adapter addresses in the machine.

Solution

The ROM address is the address in the computer's memory where the adapter's ROM will be located. The ROM address is set by using switches on the adapter.

The RAM address is the address of a unique area of memory allocated to the host machine and network adapter for read/write operations. The RAM address is selected when configuring the adapter with netconfig(ADM).

The ROM and RAM addresses must be unique on the system.

How to Determine the ROM address
--------------------------------

A useful utility called 'acfg' may be used to find the configured adapters ROM address. Run the following command :

`llipathmap`/ID/tok/acfg -D -d /tmp

This will display the ROM address in output similar to the following :

Search I/O address 0xa20: Read ROM address 0xdc000: Check ROM signature: Read 0x5 == 0x5 Read 0x0 == 0x0 Read 0x4 == 0x4 Read 0x9 == 0x9 Read 0x4 == 0x4 Read 0x3 == 0x3 Read 0x4 == 0x4 Read 0xf == 0xf Read 0x3 == 0x3 Read 0x6 == 0x6 Read 0x3 == 0x3 Read 0x1 == 0x1 Read 0x3 == 0x3 Read 0x1 == 0x1 Read 0x3 == 0x3 Read 0x0 == 0x0 Read 0x3 == 0x3 Read 0x9 == 0x9 Read 0x3 == 0x3 Read 0x9 == 0x9 Read 0x3 == 0x3 Read 0x0 == 0x0 Read 0x2 == 0x2 Read 0x0 == 0x0 Adapter Type: 0xd primary adapter found RAM Size=16K

In this example the ROM address is set to 0xdc000.

If it is necessary to modify the ROM address, use the first 6 switches on switch block 2 (S-2) on the IBM 16/4 Token Ring adapter.

For example, the ROM address CC000, which is recommended for the primary IBM 16/4 adapter, is set by the following switch settings :

Switch Block 2 (S-2)
--------------------
1    2   3   4    5    6   7 .. 12
|    |   |   |    |    |
off  on  on  off  off  on
How to Determine the RAM Address
--------------------------------

To find which RAM address is in use, use netconfig(ADM) which will display the address. Alternatively, cd to /etc/conf/sdevice.d and examine the 'tok' file. The last 2 fields in this file will specify the RAM address being used. It must be different than the ROM address. An example of the /etc/conf/sdevice.d/tok file follows :

tok    Y    0     5    0    0    a23    a23    d8000    d8000
tok    N    0     0    0    0    0      0      0        0

If necessary, use netconfig(ADM) to modify the RAM address.

See also

SCO OpenServer Release 5.0 Networking Guide IBM 16/4 ISA-16 Adapter Installation and Testing Instructions

From the Xinuos technical article database, record 107565. Reproduced with permission. The original is at www.sco.com/ta/107565, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.