Technical article 107596

How do I configure Windows 95 to connect to OpenServer 5.0.0 using PPP?

OpenServer 5.0.0

Written · Last revised

Problem

The default configuration of Windows 95 doesn't work with SCO OpenServer Release 5.0.0 over PPP.

Solution

This information has been designed with the assumption that PPP has been configured on the SCO UNIX side of the connection. A sample entry in ppphosts for a connection to Windows 95 would be:

*nppp local=ppp-slalom remote=132.147.174.1 debug=1 flow=rtscts
            ^^^^^^^^^^        ^^^^^^^^^^^^^
            unix server       Windows 95 client

Make sure you have a user "nppp" and know the password for that user.

The configuration for Windows 95 client follows:

I. From the desktop go into "Accessories" and select "Dial-Up Networking":

A. Select "Make New Connection" by double clicking on it.

B. You will be prompted to name the connection from there. Select "Configure".

1. For "General", set connection speed to that configured on the unix computer (9600 is recommended for initial configuration).

2. Under "Connection", "Connection preferences" should be
   set to:
8 data bits
None parity
1 Stop Bits

"Call preferences" should only have "Wait for dial tone before dialing" selected.

a. For "Port Settings" "Use FIFO buffers" should be
   selected.  Set the Receive Buffers to low(1) and
   the Transmit Buffers to low(1) as well.
b. Under "Advanced," "Use flow control" should be
   selected with  option "Hardware (RTS/CTS)" marked.
   "Modulation type" should be set to standard.
3. For "Options," check the box to bring up a terminal
   window after dialing.  You may find that "Display
   modem status" under "Status control" is useful for
   debugging purposes.

C. Enter the telephone number for the unix server's modem. Finish the setup procedure by selecting "Finish".

II. Select "Settings" and open the "Control Panel"

A. Select the "Internet" icon by double clicking it.

1. Choose the "Dial-Up Networking" connection you just created under "Settings".

B. Select "Modems" and highlight your modem.  Click on
   "Properties".

1. Set "Maximum speed" to the speed configured in the gettydefs file on your UNIX server (9600 is recommended for initial configuration).

C. Select "Network" and highlight "Dial-Up Adapter".  Click
   "Properties".

1. The "Driver Type" should be set to the "Enhanced mode NDIS" driver.

2. "Bindings" should be set to TCP/IP.

3. "Advanced" properties should be set to record a log
   file.  This log is kept in the Windows directory under
   the name "ppplog" and can be read with the Window's
   utility "Notepad".

IPX header compression should be turned off.

Select "OK" and exit back to the "Network" window.

D. Highlight "TCP/IP" and select "Properties".

1. Under "IP Address," specify the IP address of the Windows 95 client.

a. Enter the IP Address for the Windows 95 client in the box specified.

b. Enter the subnet mask for the Windows 95 client in the box
   given.  A typical netmask might be 255.255.255.0 or
   255.255.0.0; double-check this value with your network
   administrator before entering a value.

2. For "Gateway," enter the IP Address of the unix server.

3. If you are using Domain Name Service on your network,
   select "Enable DNS".  Enter the name of the Windows 95
   machine for "Host" and the fully qualified domain name
   for "Domain".

a. For "DNS Server Search Order" add the IP Addresses for your Primary and Secondary Domain Name Servers.

Select "OK" and exit back to the "Network" window.  Select
"OK" again to exit to the main desktop.
III. Test your connection by selecting "Programs" and from there go
     into "Accesories."  From there, select "Dial-Up Networking".

A. Double click the icon for the connection you just created.

B. If the "User name" is anything other than "nppp", change it
   to "nppp".  Enter the password.
C. Click on "Connect".
A Connecting to <connection name> status box will appear.  The
status will say "dialing" and when a connection is made, the
"Post-Dial Terminal Screen" will appear.  Type in the username
"nppp" and the password assigned to it when prompted.  You will see
several screens of "garbage" scroll by.  Press <F7> to continue.
The "Connecting to" box will say "Verifying User Name and
Password".  The connection will then establish and the box will
say "Connected" and a timer will appear.  Your PPP connection has
been successfully established.

From the Xinuos technical article database, record 107596. Reproduced with permission. The original is at www.sco.com/ta/107596, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.