Technical article 105388

How do I install OpenServer 5.0.0 with an EIDE (ATAPI compliant) CD-ROM reader?

OpenServer 5.0.0

Written · Last revised

Problem

I am installing SCO OpenServer 5.0.0 from CD-ROM media with an EIDE CD-ROM drive.

NOTE:     This information is for installing SCO OpenServer 5.0.0 products
          from the disks and media included with the 5.0.0 installation
          package only.  Newer "wd" Boot Time Loadable Drivers (BTLDs) that
          can be used in place of the ATAPI BTLD included on the SCO OpenServer
          5.0.0 Release Supplement Disk, can be obtained from the SCO website:
http://www.sco.com
see:
https://ftp.scoexpert.com/AHS/5.0/sco/5.2
or Compuserve (GO SCOFORUM).

Solution

The ATAPI BTLD is included on the SCO OpenServer 5.0.0 Release
Supplement Disk. This disk is one of four floppy disks included
with the SCO OpenServer 5.0.0 installation media package and
provides support for most EIDE CD-ROM drives.  In order to use
the ATAPI BTLD, normal IDE restrictions apply, such as a maximum
of two IDE controllers on a system, a maximum of two IDE devices
for a single IDE controller, "MASTER/SLAVE" IDE device considerations           and "PRIMARY/SECONDARY" IDE controller selections.
NOTE:  Check documentation provided by the EIDE CD-ROM hardware
manufacturer for installation procedures, especially "MASTER/SLAVE"
jumper settings and "PRIMARY/SECONDARY" controller settings before
proceeding.

Use the following steps to install SCO OpenServer 5.0.0 with the ATAPI BTLD:

1. Insert the installation boot disk provided with your SCO OpenServer 5.0.0 software in the floppy disk drive and boot the system with it.

2. Enter the following bootstring at the "Boot:" prompt:

Boot: defbootstr ahslink=ATAPI

NOTE: If the system has a primary SCSI hard disk that will be used as the boot drive, the bootstring must be altered to define that primary SCSI hard disk for the installation UNIX kernel. As an example, if the primary hard disk drive has a SCSI ID of 0, a LUN of 0, and is attached to the primary bus controlled by an Adaptec 2940 host adapter (alad), use the following bootstring:

Boot: defbootstr ahslink=ATAPI Sdsk=alad(0,0,0,0)

where, in this example, the first "0" represents the first alad controller, the second "0" represents the target ID of the drive, the third "0" represents the LUN of the drive, and the fourth "0" represents the first BUS on that controller.

The following is a list of host adapters and matching driver names that are included and supported with the SCO OpenServer 5.0.0 installation package:

Host adapter                                   Driver name
----------------------------------------------------------
Adaptec 152x                                    spad
Adaptec 154x,emulation, 164x                    ad
Adaptec 174x                                    eiad
Adaptec 274x, 284x (7770 chip)                  arad
Adaptec 294x                                    alad
Future Domain 1650, 1670, 600, 700 (1800 chip)  fdha
Future Domain 7000                              wdha
Future Domain 7000ex                            wdex
Future Domain 845, 850, 860 (950 chip)          tmcha
Olivetti ESC-1, ESC-2, and EFP                  efp
Storage Plus SCSI-AT (SUMO)                     sumo

3. When prompted, insert the ATAPI BTLD disk after the kernel has been loaded.

4. After the ATAPI driver has been loaded from the BTLD disk, you will be prompted to replace the "wd" driver (21), enter "r" to replace the "wd" driver.

5. After the new "wd" driver has been linked into the installation kernel, re-insert the Boot Disk when prompted and proceed with the installation.

6. When the "Identifying the installation media device" screen appears, choose "SCSI CD-ROM" as the media device type.

7. Select "wd" for the SCSI host adapter type.

If "wd" is not shown as a SCSI host adapter type, quit installation and start again with the following bootstring:

Boot: defbootstr ahslink=ATAPI Srom=wd(N,N,N,N)

where, in this example, the first "N" represents the primary or secondary IDE controller (0 for primary, 1 for secondary), the second "N" represents whether the IDE device is jumpered as master or slave (0 or 1), the third "N" represents the LUN of the drive (always 0 with ATAPI or wd driver), and the fourth "N" represents the BUS id on the IDE controller (always 0 with ATAPI or wd driver). It may also be necessary to include "Sdsk" information from step 2 in this new bootstring.

NOTE:  If "wd" is not shown as a SCSI host adapter type, the
ATAPI (wd) driver was not able to detect the EIDE (ATAPI compliant)
CD-ROM drive. Make sure the settings for the CD-ROM, other IDE
devices and CMOS settings for IDE devices on that system, are
correct.  On some systems it may be necessary to set that EIDE
CD-ROM as a device on the "Primary" IDE bus as appropriate. That is,
if the primary IDE bus only contains the EIDE CD-ROM then it should
be jumpered as "Master"; if the EIDE CD-ROM is the second device
with a boot drive as "Master" then the CD-ROM should be jumpered as
"Slave".  It may be necessary to obtain the latest SCO  Advanced
Hardware Supplement BTLD disk and use that in place of the ATAPI
BTLD supplied with the SCO OpenServer 5.0.0 Release Supplement
Disk using instructions included with that BTLD disk.

8. If the CD-ROM drive is attached to the Primary IDE controller in system with one or two IDE controllers, select "0" for the host adapter number.

If the CD-ROM drive is attached to the Secondary IDE controller in a system with two IDE controllers, select "1" for host adapter number.

9. If the CD-ROM drive is configured as a Master device, select "0" for its SCSI ID.

If the CD-ROM drive is configured as a Slave device, select "1" for its SCSI ID.

10. Select "0" for the SCSI LUN of the CD-ROM drive.

11. Select "0" for the SCSI bus number.

See the SCO OpenServer Handbook to continue installation.

See also

man (HW) boot, man (ADM) boot, man (HW) bootstring

From the Xinuos technical article database, record 105388. Reproduced with permission. The original is at www.sco.com/ta/105388, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.