Technical article 105865

How do I install SCO OpenServer Enterprise 5.0.4 on a DEC Celebris 5100 with IDE CD-ROM and hard drive?

OpenServer 5.0.2OpenServer 5.0.4

Written · Last revised

Problem

I am trying to install SCO OpenServer Enterprise 5.0.4 on my DEC Celebris 5100. It recognizes all of my hardware but when I get to the point where it is "Making Filesystems" and extracting from the media source (IDE CD-ROM), it starts counting and then stops. At that point, I am unable to interrupt the installation process, and the system freezes.

Cause

There are two values in the Celebris' CMOS that are specific to
the function and operation of "IDE hard drives" and if left at
the default value of "Enabled" then the problem will occur every
time you try to install.  The items that need to be disabled are:
1. 32 BIT I/O
2. Read Ahead Mode

Solution

After making sure that the IDE CD-ROM is set for and cabled as MASTER device on the Secondary IDE controller, enter the system CMOS during the initial boot process by pressing the <F2> key.

The following is a partial example listing of the "Main" screen in the system CMOS:

IDE Adapter 0 Master    (C:540Mb)
IDE Adapter 0 Slave     (None)
IDE Adapter 1 Master    (None)
IDE Adapter 1 Slave     (None)

NOTE: Do NOT change these settings. There are no specific settings for IDE CD-ROM devices available.

Once in the system CMOS "Main" screen, follow the next steps to change the values for "32 BIT I/O" and "Read Ahead Mode":

1. Using the down-arrow key, highlight the line for
"IDE Adapter 1 Master   (None)", and press <Enter>.

2. The following is a partial example listing of the screen for "IDE Adapter 1 Master" configuration:

Multi-Sector Transfers:         [8 sectors]
LBA Mode Control:               [Disabled ]
32 BIT I/O:                     [Enabled  ]
Transfer Mode:                  [Standard ]
Read Ahead Mode:                [Enabled  ]

NOTE: "32 BIT I/O" must be disabled in order to disable "Read Ahead Mode".

3. Using the down-arrow key, highlight the line for "32 BIT I/O" and change the value to "Disabled" with the "+ or -" keys.

4. Using the down-arrow key, highlight the line for "Read Ahead Mode", and change the value to "Disabled" with the "+ or -" keys.

5. Press <Esc> to return to the "Main" screen and use the
right-arrow key to open the "Exit" screen.  "Save Changes and
Exit" will already be highlighted; press <Enter> twice to
save changes and exit.
6. This will reboot the system.  When the screen goes blank, simply
power the system off.

NOTE: The IDE CD-ROM will not be reported to the screen during P.O.S.T.(Power On System Test).

7. Insert the Installation boot floppy disk and power the system
back on.  At the Boot: prompt press <Enter>.

8. Upon arrival at the "Identifying the Installation Media Device" screen, verify that the screen appears as follows:

5.0.2;
Per the Release Notes, select "SCSI CD-ROM" as the installation
media and "wd" as the adapter type.  Also select the following:
SCSI Host Adapter     1
SCSI ID               0
SCSI LUN              0
SCSI BUS              0
5.0.4;
        Media device to be used: IDE CD ROM
        IDE Controller:          Secondary
        Master or Slave:         Master

NOTE: Make the necessary adjustment to the above examples by using the directions at the bottom of the screen.

9. Press <Enter> to "Accept Settings".  You will then be
prompted to insert the CD-ROM media.  Do so and press <Enter>
again.

10. Continue the installation process and enter the information that is required.

11. When you get to the "Preparing Your Disk and Choosing Software"
screen, press the "spacebar" on "Hard Disk Setup".  This will take
you to the "Setting Up Your Hard Disk" screen.  Make your choices
of partition(s) and filesystem(s).  Set "Disk 0 Bad Track Type" to
"None" and the press <Enter> to "Accept Settings".  This will
return you to the "Preparing Your Disk and Choosing Software"
screen. Press <Enter> to "Accept Settings" and continue with the
installation.

From the Xinuos technical article database, record 105865. Reproduced with permission. The original is at www.sco.com/ta/105865, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.