Technical article 105643

How do I perform an in-place upgrade with OpenServer 5.0.4 on the Compaq ProLiant 5000 using the integrated SCSI controller?

OpenServer 5.0.4

Written · Last revised

Problem

What is the procedure to correctly upgrade SCO OpenServer 5.0.0, 5.0.2 to OpenServer 5.0.4 on the ProLiant 5000?

Solution

As per the Release Notes, SCO recommends that your 5.0.0 or 5.0.2
system be completely backed up prior to the update.  It is also
recommended that the integrity of the backup(s) be verified.  Also,
it is stated in the Release Notes (p. 22) that the existing Compaq
EFS be removed from the 5.0.x server prior to the upgrade.  For
additional information on removing the EFS, reference the EFS
Documentation floppy diskette.

Although there may be slight variations in the flow of this procedure based on how you respond to prompts, the process will generally be as follows:

Boot the server from the SCO Boot Floppy.

For a first time installation, in response to the Boot: prompt, type 'link' as follows:

SCO OpenServer(TM) Release 5
Boot
: link

You will then be prompted for which packages you want to link into the kernel.

What packages do you need linked in the system, or q to quit?: cha

It would also be correct to respond as follows:

What packages do you need linked in the system, or q to quit?: CUCHA

You will see:

fd(64)unix root=ram(7) ram.preload=7 swap=none dump=none nbuf=100 ramdisk=fd(64) rootFS link="cha" btld=fd(60)

or

fd(64)unix root=ram(7) ram.preload=7 swap=none dump=none nbuf=100 ramdisk=fd(64) rootFS link="CUCHA" btld=fd(60)

Sizing memory
................
Loading kernel fd(64)unix .text
.....................................
Loading kernel fd(64)unix .data
.....................................
Loading kernel fd(64)unix .bss

Loading kernel symbol table, this may take a few minutes

Please insert the fd(60)cha volume and press <Return>, or 'q' to quit.

At this point, insert the BTLD diskette from EFS 5.14 or later.
Then press <Enter>.  Eventually, you will see:
Insert the Boot Disk and press <Return>

At this point, insert the original SCO OpenServer Release 5.0.4 Boot floppy which came with your CD-ROM media from SCO and press <Enter>.

Eventually you will see the "RESTRICTED RIGHTS LEGEND" screen.

Proceed to the "Identifying the installation media device" screen. Press the space bar to toggle to SCSI CD-ROM from SCSI Tape.

Media device to be used: SCSI CD-ROM
SCSI Adapter Type:     cha
SCSI Host adapter:     0
SCSI ID:               5
SCSI LUN:              0
SCSI BUS:              0
Insert the CD-ROM media when prompted.

After entering the licensing information, you will be prompted for what type of a installation you are performing on a "Suitability for automatic Upgrade" screen.

Highlight "Upgrade" and press <Enter>.  Again, press <Enter> on
the "Upgrade" Installation type, and accept the response.

Highlight "OK" for the installation to proceed.

Several additional messages will appear on the screen during the installation process, including the "Percent Installation Complete". Finally, you will see:

Installation and initial configuration of SCO OpenServer Enterprise System is Complete.

Before you use the system:

-- Perform any additional configuration needed, as described in the Release Notes.

-- Create an emergency root and boot floppy set as described in the SCO OpenServer Handbook.

(EOF)
Press <Enter> to continue:
After pressing <Enter>:
At the "Power Off or Reboot" prompt, remove the floppy disk
from the drive and press any key to reboot.  The screen clears,
then displays the "Boot:" prompt.
Press <Enter> to continue

Again, press <Enter>, and you will see:

**     Safe to Power Off     **
            -or-
**  Press any Key to Reboot  **

Remove the media and press any key to boot the 5.0.4 system.

From the Xinuos technical article database, record 105643. Reproduced with permission. The original is at www.sco.com/ta/105643, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.