Technical article 104918

I am trying to install an ATAPI/WD CD-ROM as a secondary device.

OpenServer 5.0.0

Written · Last revised

Problem

I am trying to install one ATAPI/WD CD-ROM as a secondary device,
but the device is not recognized by the installation process in the
test for device presence.  The LED of the controller stays on
"searching" for the CD-ROM device.  My system may hang and then
need to be rebooted.

Cause

These problems may occur because:

- The BIOS is not configured correctly.

- The CD-ROM is not configured with the correct jumper settings.

- The CD-ROM is on the secondary IDE controller and does not have the correct jumper setting.

- Some CD-ROMs or IDE controllers are only supported with AHS 5.1.

- The entries displayed on the screen during the boot process don't mean that the CD-ROM has been recognized.

%adapter 0x01f0-0x01f7  14 - type=wd ha=0 id=7 bus=0 fts=d

Solution

1.The BIOS must be configured similar to this example:

Primary Device or Master Disk = Hard Disk (specify type)
Secondary  Device or Slave Disk = SCSI Non IDE Device or CD.
On most BIOS, the CD option is not present.  Most BIOS support
the autodetect option.
2. The CD-ROM must be configured according to the specification
of the controller.  Depending on the controller, and the type of
the IDE cable, it may be jumpered as Slave or CS (Cable Select).
On some HP PCs, it has to be jumpered as CS.  Normally, it is set
to Slave.  Check the instructions or the manual for your controller
for further information.

3. If you have two controllers, and on the secondary controller the only device is the CD-ROM, configure the CD-ROM jumpers as a Master.

4. Some CD-ROMs and IDE controllers are only supported with AHS
5.1.  Make sure that the driver in AHS 5.1 has changed its name
from ATAPI to WD.

5. It has been tested that the same CD-ROM which is normally working with the standard ATAPI driver will not work on different PCs. This may be due to the controller type or some timing differences. In this case, installing AHS 5.1 may solve the problem.

6. The suggested procedure for the installation of the ATAPI or
AHS 5.1 WD driver follows.  Boot the system from the boot floppy.
At the boot prompt, type:
defbootstr ahslink=ATAPI

(if you are using the standard BTLD ATAPI floppy driver).

-OR-
defbootstr ahslink=wd

(if you are using the AHS 5.1 wd driver).

After the request for the ATAPI or the WD floppy driver, you will
be asked to add or replace the driver.  Type 'r' to replace the
driver.
In the installation menu, choose:
- SCSI CD-ROM.

- wd for the host adapter type.

- 0 (CD-ROM is connected on primary IDE controller) or 1 (CD-ROM is connected on secondary IDE controller) for SCSI host adapter number.

- 0 (CD-ROM is Master) or 1 (CD-ROM is Slave or CS) for SCSI ID.

- 0 for SCSI LUN and SCSI Bus number.

See also

SCO OpenServer Release Notes and AHS 5.1 Release Notes.

From the Xinuos technical article database, record 104918. Reproduced with permission. The original is at www.sco.com/ta/104918, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.