Technical article 105523

I can't install using a CD-ROM connected to the 2nd alad adapter.

OpenServer 5.0.0OpenServer 5.0.2

Written · Last revised

Problem

I am trying to install SCO OpenServer on a system which has the
disk on the primary 7860/7870/7880/2940 (alad) controller and
the CD on another 7860/7870/7880/2940 alad controller.  The
standard installation diskette can only access one alad
controller.

During the installation, IQM asks what device I want to install from. When I choose SCSI CD-ROM, I am unable to choose the relevant configuration information.

Solution

Use the SLS OSS444A installation diskette in place of the standard SCO OpenServer diskette. The SLS OSS444A diskette is identical to the standard SCO OpenServer 5.0.2 installation diskette, except that it can access up to four alad controllers.

If you are not sure of the configuration of your machine, it is recommended that you gather this information -- either by physically checking the machine, or by entering the Adaptec bios-setup code during the machine startup-sequence.

During the boot sequence of the SLS OSS444A diskette, you should
see more than one %alad entry written to the screen. After some
time, IQM asks what device you want to install from.  At that point,
you will be able to choose from up to four alad controllers.

If you are not sure which adapter your CD-ROM is connected to, select each host adapter until the IQM confirms that the CD-ROM has been detected.

After successfully installing with SLS OSS444A, it is necessary to configure the extra alad controller into the system.

Change directories to /etc/conf/sdevice.d and edit the file called "alad". Duplicate the single line found as many times as you have controllers. For example, if you have two controllers, then you should have two lines in the alad file. They will look like the following:

alad    Y       1       5       0       0       0       0       0       0
alad    Y       1       5       0       0       0       0       0       0

Then change directories to /etc/conf/cf.d and relink the kernel using "./link_unix -y". Reboot the system.

NOTE:     Do not use SLS OSS444A with SCO Internet FastStart Release 1.0.0
           or 1.1.0.
Dear SCO Customer,

The enclosed Support Level Supplement (SLS) OSS444A allows you to install SCO OpenServer Release 5.0.2 on a system that has a CD-ROM drive attached to a non-primary "alad" controller. (This supports the 7860/7870/7880 chips and the 2940 card.)

Note: Do not use SLS OSS444A with SCO Internet FastStart Release 1.0.0 or 1.1.0.

INSTALLATION INSTRUCTIONS
To use this SLS, replace the 5.0.2 installation diskette with the SLS
OSS444A diskette.  The SLS OSS444A diskette is identical to the standard
SCO OpenServer 5.0.2 installation diskette, except that it can access up
to four alad controllers.

After installation, manually edit the following files to allow continued access to the CD-ROM drive.

1. Log in as root.

2. Change directories to edit the alad sdevice entry:

cd /etc/conf/sdevice.d

3. Edit the file called "alad" and duplicate the single line found as many times as you have controllers. For example, if you have two controllers, then you should have two lines in the alad file. They will look like the following:

alad    Y       1       5       0       0       0       0       0       0
alad    Y       1       5       0       0       0       0       0       0
4. Relink the kernel:
cd /etc/conf/cf.d
./link_unix -y

5. Reboot the system to use the new kernel:

/etc/shutdown -y -g0
or
init 6

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 105523. Reproduced with permission. The original is at www.sco.com/ta/105523, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.