Technical article 105037

Installation on IBM PC Server 310 MCA machine hangs at boot letter G.

OpenServer 5.0.0

Written · Last revised

Problem

Installation of SCO OpenServer Release 5.0.0 on an IBM PC Server 310 with the MCA/PCI riser card hangs when it displays the letter G during the boot letter sequence phase.

Cause

Some devices on the IBM PC Server 310 MCA model, which are
attached to the motherboard/planar, are recognized as ISA devices.
In effect, it gives the machine a combined architecture of ISA and
MCA and PCI.  However, only MCA and PCI cards can be inserted into
the riser card.

Solution

During installation, use Support Level Supplement (SLS) OSS431A. SLS OSS431A consists of a replacement boot and a supplemental diskette.

The replacement boot disk contains a new boot kernel that includes the modified drivers. This will enable the machine to be installed.

The supplemental disk contains the new drivers in the form of a BTLD.

NOTE:     This SLS is NOT required for the IBM PC Server 310 ISA/PCI model.

See the attached SLS OSS431A cover letter for installation instructions.

Dear SCO Customer,
The enclosed Support Level Supplement (SLS) OSS431A, the IBM PC Server 310
Installation Supplement, consists of a replacement boot and supplemental
diskette which will enable the IBM PC Server 310 MCA/PCI machine to be
installed.  Modified device drivers are required to allow this machine to
install and function correctly.

This SLS is NOT required for the IBM PC Server 310 ISA/PCI model.

SLS OSS431A applies only to these products:

SCO OpenServer Enterprise System Release 5.0.0 SCO OpenServer Desktop System Release 5.0.0 SCO OpenServer Host System Release 5.0.0

NOTE: Earlier versions of SCO Open Server, SCO Open Desktop and SCO UNIX
System V/386 are not supported.  This procedure only applies to SCO OpenServer
Release 5.

The SLS OSS431A replacement boot disk obsoletes the boot disk from the original distribution.

I. BOOTING - OPERATING SYSTEM INSTALLATION
Your hardware configuration SCSI disk ID default may differ from the SCO
default of 0.  If so, use a bootstring at the boot prompt to tell the
software on which SCSI ID the disk drive is configured.

The SCSI IDs are displayed after the POST and the option to enter the Adaptec AHA-2940/AHA-2940W SCSISelect(TM) Utility.

In the installation documentation, the SCSI disk ID is set to 6.  The
CD-ROM is set to 3.  Change these according to your system configuration.

1. Place the SLS OSS431A replacement boot disk in the floppy disk drive.

2. Manually reset the system or turn the power on.

3. When the "Boot:" prompt appears, type:

defbootstr Sdsk=alad(0,6,0)
NOTE: If your disk is configured to SCSI ID 0, press <Enter>
      at the "Boot:" prompt instead of entering the above
      bootstring.  The CD-ROM SCSI ID may be selected in the
      installation device menu.

4. Follow the installation procedures as outlined in the Release and Installation Notes.

5. When the installation is complete, you will see the "SAFE to POWER OFF" message.

a. Make sure the SLS OSS431A replacement boot disk is in the floppy disk drive. b. Press <Enter> to reboot the computer. c. When the Boot: prompt appears, type:

fd(64)unix dump=hd(41) swap=hd(41) root=hd(42) Sdsk=alad(0,6,0)

After loading text, data and displaying the hardware device screen, you may see:

CONFIG: itimer: Not installed ERROR: unable to open /dev/log

These errors may be safely ignored.
The following text will be displayed:

Type CONTROL-d to proceed with normal startup, (or give root password for system maintenance)

Enter the root password and press <Enter>.

6. Remove the SLS OSS431A boot disk from the floppy disk drive.

7. Insert the SLS OSS431A supplemental disk into the floppy disk drive.

8. At the prompt, type:
installpkg
Press <Enter>.  When the command has completed, ensure that the
SLS OSS431A supplemental disk is inserted and press <Enter>.

When prompted for the names of the packages to install, type:

nmi pic
Press <Enter>.  You will be informed that a driver already exists
and asked whether you want to replace it with the new version.
Answer "y" and press <Enter>.

Repeat the above procedure for the pic driver.

When the installation is complete, relink the kernel by typing:

cd /etc/conf/cf.d
./link_unix

Answer "y" when asked if you want to the kernel to boot by default. Answer "y" when asked if you want the kernel environment rebuilt.

Remove the SLS OSS431A supplemental disk from the floppy disk drive. Type "reboot" and press <Enter> to restart the system.

II. NOTES ON NETWORK INSTALLATION

This patch is unable to be installed over the network.

III. PATCH REMOVAL

This patch should not be removed as your system will not function without it.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 105037. Reproduced with permission. The original is at www.sco.com/ta/105037, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.