Technical article 109373

Installing SCO OpenServer 5.0.4 on an IBM Netfinity 3500.

OpenServer 5.0.4

Written · Last revised

Problem

When installing an IBM Netfinity 3500, these errors, or any combination of them, may occur:

(1) "F eiadinit
    NOTICE: k_trap. Unexpected NMI in system mode!" and the
    system continues;

(2) "System error 5" while getting fs type;

(3) "F aladinit" and then the system hangs indefinitely.

Solution

Each of the above errors is addressed below:

	  Note: To ensure the best success for the following solutions it is
	 	recommended to make sure that the IBM Netfinity 3500 has a
		minimum BIOS version of "29".  To view and obtain the flash
		updates for the IBM Netfinity 3500 visit;
			ftp.pc.ibm.com/pub/pccbbs
(1) The error:

"F eiadinit" "NOTICE : k_trap. Unexpected NMI in system mode".

is due to a problem in BIOS version 25.  You should upgrade
your BIOS to the latest version, which is available on the
IBM BBS. The BIOS upgrade can also upgrade the SCSI BIOS for
the Adaptec 7895, as well as the system BIOS.

(2) "System error 5" while getting fs type may occur if the system is not initialized properly after the BIOS has been upgraded. To initialize the system, do the following:

(a) Power the system on.

(b) When the "Press F1 for Configuration/Setup" message appears on the IBM logo screen, press <F1>.

(c) At the "Configuration/Setup Utility" menu, highlight "Load
    Default Settings" and press <Enter>. Press <Enter> again to
    continue.  At this point, you might also set the correct date
    and time.

(d) Highlight "Exit Setup" and press <Enter>.

(e) Highlight "Yes, save and exit the Setup Utility" and press <Enter> to restart the system.

(f) When a message similar to the following is displayed, press <Ctrl><A>:

Adaptec AIC-7895 SCSI BIOS v1.31 (c). 1997 Adaptec, Inc. All Rights Reserved.

<<< Press <Cntrl><A> for SCSISelect(TM): Utility! >>>

(g) Highlight "00:09:A" at the "Bus:Device:Channel" menu; press <Enter> to display the "Options" menu.

(h) Highlight "Configure/View Host Adapter Settings"; press <Enter> to display the "Configuration" menu.

(i) Press <F6> "Reset to Host Adapter Defaults" to reset the SCSI settings.

(j) Highlight "Yes" to "Reset All Options to Default Settings?";
    press <Enter> to reset defaults.  Press <Esc>.
(k) Highlight "Yes" to "Save Changes Made?"; press <Enter> to
    return to the "Options" menu. Then press <Esc> to return to
    the "Bus:Device:Channel" menu.

(l) Highlight "00:09:B" at the "Bus:Device:Channel" menu; press <Enter> to display the "Options" menu.

(m) Highlight "Configure/View Host Adapter Settings"; press <Enter> to display the "Configuration" menu.

(n) Press <F6> "Reset to Host Adapter Defaults" to reset the SCSI settings.

(o) Highlight "Yes" to "Reset All Options to Default Settings?";
    press <Enter> to reset defaults.  Press <Esc>.

(p) Highlight "Yes" to "Save Changes Made?"; press <Enter> to return to the "Options" menu.

(q) Press <Esc> to return to the "Bus:Device:Channel" menu.

(r) Press <Esc> again.

(s) Highlight "Yes" to "Exit Utility"; press <Enter>.

(t) Press any key to restart the system.

(u) Initialization is now complete.
(3) The error "F aladinit" occurs during installation and then
    the system hangs indefinitely.  This is due to the default
    "alad" driver in the SCO OpenServer 5.0.4 boot kernel not
    supporting the Adaptec 7895 chipset.

The Adaptec driver for the 7895, which IBM is supporting, is version 2.10 or 2.11. This is available on the IBM BBS at this URL:

ftp://ftp.pc.ibm.com/pub/pccbbs/pc_servers/10l9294.exe

The README file is located at this URL:

ftp://ftp.pc.ibm.com/pub/pccbbs/pc_servers/10l9294.txt
10L9294.EXE creates a diskette for the Adaptec 7800 Family
Manager Set v2.11 S3 for SCO OpenServer Release 5 and SCO
UnixWare 2.0x or 2.1.  This driver is used for IBM machine
type 8644.

To add the BTLD at boot time, do the following:

(a) At the "Boot:" prompt, type "ahslink".

(b) When asked for name of package, type "alad325".

(c) After the kernel loads, but before it runs, "link" prompts you to insert "7800 Family Manager" diskette.

NOTE: You will be notified that an existing aladinit driver already exists and asked which routine you wish to replace. Choose routine 25 to replace and continue with the installation.

From the Xinuos technical article database, record 109373. Reproduced with permission. The original is at www.sco.com/ta/109373, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.