Technical article 107612

"network connection lost" or other network errors using Compaq NetFlex3 NICs.

OpenServer 5.0.0OpenServer 5.0.2

Written · Last revised

Problem

My NetFlex3 card is reporting errors such as:

WARNING: cet: unit 0: network connection lost. Attempting to restart. Mon May 20 12:46:39 1996

and/or:

NOTICE: cet: unit 0: restarted successfully. Mon May 20 12:46:54 1996

The messages that scroll on the console may eventually overflow the error logs, and networking on the machine may hang.

Cause

According to Compaq, this error-reporting is a feature that is
built into the Compaq "Netelligent Controller" family, to which
the NetFlex3 belongs.  The card sends test frames out to the
network, and if it does not receive a response within a set
time frame, the card restarts itself.
Network connection-lost messages indicate that the driver is
unable to successfully transmit frames and has initiated a
recovery attempt.  This can result from any of the following
conditions:
- The network cable is disconnected.

- The hub or concentrator has lost power.

- Incompatibility between the NetFlex-3 PHY module and the hub.

- "capture effect" on CSMA/CD networks.

Solution

In order to alleviate some of the problems associated with this network monitoring, Compaq has modified the functionality in EFS 5.10 and later which allows the user to control the advanced monitoring functionality and other features. The latest version of the Compaq EFS is always available from Compaq's bulletin board (ftp.compaq.com)

Use the Compaq EFS 5.10 or later if you are using an SCO operating system Release 5.x. You can obtain the Compaq EFS 5.12 from SCO's bulletin board (ftp.sco.com, www.sco.com, 408-426-9495) as SCO EFS 153.

Similarly, these problems have been alleviated in the Compaq EFS 3.10,
which is available for SCO Release 3.x operating systems.  The Compaq
EFS 3.10 is available from Compaq, or you may obtain it from SCO's
bulletin board as SCO EFS 152.

Alternatively, you can set your Netflex III card into Netflex II mode through your Compaq EISA configuration utility.

NOTES:    These notes are from the Compaq EFS 5.10.  See your complete
          EFS documentation for more details.
NetFlex-3 Option Override configuration
Certain operating parameters specific to the NetFlex-3 models may
be overridden.  The options that may be overridden are:
Heartbeat - Enables/Disables generation of a network error event
            interrupt to the driver.  This is used to detect a
            problem with the ethernet media when no Link Status
            indication is available.  This option is enabled by
            default.

Media Connector - Specifies a particular type of media connector. It may be used to force the use of UTP vs BNC for example. This option is automatically configured by default.

Media Speed -  Specifies a particular media speed.  It may be used
               to force the speed to 10Mbps when it would normally
               be 100Mbps, for example. This option is automatically
               configured by default.
Frame Format - Specifies a particular frame format to be used when
               in 802.12 100VG AnyLAN mode.  It may be used to force
               the frame format to token ring when it would normally
               be ethernet, for example. This option is automatically
               configured by default.

To override these options, the following procedure must be applied:

(1) Edit the .info with "vi" or another suitable editor. Append a
    line to the bottom of the .info file, using the examples below
    for each option:
heartbeat {unit number} {enable/disable}
media-connector {unit number} {utp}
media-speed {unit number} {10mbps/100mbps}
frame-format {unit number} {ethernet/token-ring}

(2) Reboot the system. When the cet driver is restarted, the option will have taken effect. Removing these options from the .info file and rebooting the system restores the default behavior.

Network High-availability Features Configuration

Network high-availability features reduce network downtime in the following ways:

(1) Detection of network faults. (2) Annunciation of network faults. (3) Recovery from network faults where possible. (4) Collection and display of advanced diagnostics for early warning of impending network faults.

The types of network faults that can be detected are:

(1) Cable failures. (2) Hub or concentrator port failures. (3) Hub or concentrator power failures. (4) Network interface driver failures. (5) Network interface hardware failures.

The Compaq NetFlex Interface Manager (cpqnim) application program
provides a user interface to the configuration and display of these
features.  Any interface type supported by the "cet" driver may be
configured to support these features.

See also

See other articles in this database:
TA105297, "How can I get the Compaq Extended Feature Supplement
(EFS) 3.10?"
TA105499, "How do I obtain the Compaq Extended Feature Supplement
(EFS) 5.12?"

From the Xinuos technical article database, record 107612. Reproduced with permission. The original is at www.sco.com/ta/107612, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.