Technical article 105722

No files are scanned when I perform a manual scan using Interscan VirusWall.

OpenServer 5.0.0OpenServer 5.0.2OpenServer 5.0.4OpenServer 5.0.5

Written · Last revised

Problem

I have installed and configured SCO InterScan VirusWall through the SCO Interscan VirusWall admin page using my browser. When I select the option, "Scan Entire Server", make my selections (for example, filesystem or directory to scan) and perform a "Scan Now" operation, in the next screen I get this message:

scanning . . . No file scanned No virus found

If I attempt a manual scan from the command line, using the command /etc/iscan/config, I get the following message:

Scanning ... Failed to access temp file vsslog<log#>: END

As a result files are never scanned.

Cause

VirusWall is attempting to scan the filesystem or directory, but is unable to due to either a corrupted or missing Virus Pattern file in the /etc/iscan directory. In some installations the Virus Pattern file, lpt$vpn.<patternID>, does not get copied to the /etc/iscan directory correctly.

Solution

To replace or copy the Virus Pattern file to the proper directory, take these steps:

(1) Log in as root. From the Unix prompt, issue the command:

cd /opt/K/SCO/VWbase/1.52/etc/iscan

Do a listing for lpt$vpn.225 as follows:

ls -al lpt\$vpn.225
(2) If the file does not exist, then customextract(ADM) it
    from the original SCO distribution media.  For example,
    extracting the file from a CD-ROM, issue the following
    command at the Unix prompt, from the root directory:
customextract -m /dev/cd0 \
/opt/K/SCO/VWbase/1.52/etc/iscan/lpt\$vpn.225
(Note: the "\" at the end of the lines above and below are meant
to escape the next character, a carriage return, and continue
the line.  Likewise, the "\" before the "$" sign in lpt$vpn.225
is meant to escape the "$".)

(3) If the file does exist, then issue the following command at the Unix prompt:

cp /opt/K/SCO/VWbase/1.52/etc/iscan/lpt\$vpn.225 \
/etc/iscan/lpt\$vpn.225

(4) Then issue the following command at the Unix prompt:

cd /etc/iscan

and perform a listing as in step 1 above to verify that the file was copied correctly as lpt$vpn.225.

(5) From the Unix prompt, issue the commands:

chmod 444 /etc/iscan/lpt\$vpn.225
chown iscan /etc/iscan/lpt\$vpn.225
chgrp iscan /etc/iscan/lpt\$vpn.225

(6) The VirusWall http daemon must be stopped and restarted. Issue the following command from the Unix prompt to get the process ID (pid) of httpd:

ps -ef|grep /etc/iscan/httpd

Then issue the following commands from the Unix prompt:

kill <pid>
/etc/iscan/httpd
NOTES:    The VirusWall Pattern file, lpt$vpn.225, cannot be a symbolic
          link in /etc/iscan, and must be a copy of the original file as
          installed from /opt/K/SCO/VWbase/1.52/etc/iscan directory. The
          above procedure must be followed after updating the Virus Pattern
          file as well.

See also

TA105723 "VirusWall Pattern file update error: 'Unable to connect to virus pattern server, err=11.'".

From the Xinuos technical article database, record 105722. Reproduced with permission. The original is at www.sco.com/ta/105722, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.