Technical article 107599

What are some tips for configuring 100Mbit network cards(PCI or EISA) under SCO?

OpenServer 5.0.0

Written · Last revised

Problem

I am having difficulty getting my 100Mbit network card recognized or functioning on the SCO server.

Cause

There can be problems with the card settings, system BIOS, PCI
slot, cabling, driver, as well as a number of other issues.  Any
of these can cause the card to fail.

Solution

There are several possible solutions, depending on the exact
problem.  Here are some areas to check:
CONFIGURATION:

As always, the settings you define for your NIC through netconfig must match what the card is physically set for.

For EISA machines, make sure the card is configured in the EISA configuration utility (ECU).

In most cases, the PCI computer automatically (and invisibly)
configures the adapter for the slot it is in.  If this doesn't
happen, you may have to configure the computer to work with the
adapter.

Contact your computer's manufacturer to make sure you're using the latest BIOS.

1. Put the adapter in a busmastering slot in the computer.

2. Start the computer.

3. Make sure the BIOS is set up correctly.

In some PCI computers, you may need to enable the PCI slot using
the BIOS Setup program.  This is especially common in PCI computers
with Phoenix BIOSs.  After turning on the computer, enter the BIOS
Setup program during system initialization (usually by pressing F1,
F2, or Ctrl-Alt-S).  The key you press is dependent upon the computer
you have.

Once in BIOS Setup, find the entry for PCI slots. Try using these parameters:

PCI Slot#:     Slot where the adapter is installed (1-3)
Master:        ENABLED
Slave:         ENABLED
Latency Timer: 40
Interrupt:     Choose any one of several that Setup provides.
Edge-level:    Level
The exact wording of the parameters varies with computers.  Save
the changes, exit BIOS Setup, and continue with the installation.
(Note: Some PCI Bios Setup programs require you to enable the slot
for busmaster/master.  If your card's documentation recommends
some other specific setting, use that.)
OTHER ISSUES:
Hubs:
100Mbit network cards require 100Mbit hubs.  Most can be used
with any hub that supports 100Base-TX.
Cabling/Media:

* The cabling should comply with the IEEE 802.3 10BASE-T standard for 2-pair, Category 5, UTP cable.

* The cable between the computer and the hub should be less than 100 meters long.

* Many 100Mbit adapters do not support pre-10BASE-T concentrators.

* Incorrect wiring will cause the link to fail or a hub may not be able to detect a workstation.

* Pay close attention to the type of media selected during the
  configuration through netconfig.  That is, make sure you choose
   10Mbit or 100Mbit according to your cable type; likewise, if
   you have shielded or unshielded cabling, or full-duplex
   cabling, you will need to select that properly when given the
   choice in netconfig.  Not all network cards have all these
   options, but when presented with a choice it is important to
   give the correct answer.  When in doubt, contact the NIC
   manufacturer.
Link integrity:
Some cards have LEDs which are useful for diagnosis.  Often,
there is an LED to indicate a successful link; one for traffic
flowing across the network, and one to indicate whether the
connection is truly 100Mbit.  Just because the network LED is
flickering, we cannot assume the card itself is functioning; only
the link LED informs us the card is delivering packets.
Drivers:
Some cards can be "seen" and even configured with more than one
driver.  Make sure you are using the latest version as well.
For both OpenServer 5 and Open Desktop 3 systems, we recommend
downloading and installing the latest Advanced Hardware
Supplement (AHS) drivers for your system.  Or, for vendor-
supported cards, contact the vendor to obtain the latest
drivers.

From the Xinuos technical article database, record 107599. Reproduced with permission. The original is at www.sco.com/ta/107599, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.