Technical article 105925

What is SLS OSS463B, the Multiple SCSI Install N0 and BTLD Supplement?

OpenServer 5.0.4

Written · Last revised

Problem

It isn't possible to install SCO OpenServer Release 5.0.4
with a CD-ROM drive that is attached to a SCSI adapter, other
than the one to which the root drive is connected.  It also
isn't possible to use a Boot Time Loadable Driver (BTLD) during
the installation if the CD-ROM and the root drive are attached
to different SCSI adapters of the same type.

Solution

Support Level Supplement (SLS) OSS463B, the Multiple SCSI Install
N0 and BTLD Supplement, corrects this installation problem. This
SLS consists of an N0 and BTLD diskette.  The N0 replaces the N0
diskette originally packaged with the SCO OpenServer product. The
BTLD is provided to allow the automatic installation of updated
drivers during the installation process.  The BTLD contains the
updated drivers:
Alad    Adaptec SCSI HBA
Arad    Adaptec SCSI HBA
Mdac    Mylex   SCSI RAID HBA
Slha    Symbios SCSI HBA
Wd      IDE/ATAPI interface

The N0 diskette contains the previous corrections included in OSS463A, an updated boot-time linker and a new UNIX kernel with the same updated drivers included on the BTLD diskette.

See the attached cover letter that accompanies this SLS for more information, including installation instructions.

Dear SCO Customer,
The enclosed Support Level Supplement (SLS) OSS463B, the Multiple SCSI
Install N0 Supplement, allows for the installation of SCO OpenServer 5.0.4
operating systems on computers with CD-ROM drives attached to secondary
host adapters.  Previously, it was only possible to use these CD-ROM drives
by configuring them after the installation of the operating system.

SLS OSS463B is intended for use on these products:

SCO OpenServer Enterprise System Release 5.0.4 SCO OpenServer Desktop System Release 5.0.4 SCO OpenServer Host System Release 5.0.4 SCO OpenServer Internet FastStart Release 5.0.4

SLS OSS463B consists of a replacement N0 and an additional BTLD diskette. The N0 is to be used in place of the original N0 floppy provided with the installation media. The BTLD is to be used at install time if any of the drivers shown below are required for installation:

alad      Adaptec 294x (7870 & 7880 Chip)
arad      Adaptec 274x (7770 Chip)
mdac      Mylex Disk Array Controller
slha      Symbios Logic (formerly NCR MPD) 53c8xx Host Adapters
wd        Enhanced IDE, ATAPI Interface (for tapes and CD-ROMs)

The changes made in this SLS only affect installation procedures; there is no post installation requirement to install software from the replacement N0 or BTLD.

INSTALLATION INSTRUCTIONS
Because SLS OSS463B is a replacement N0 diskette, the SLS takes effect upon
system installation.  See the SCO OpenServer product documentation for
software installation instructions.  If one of the updated drivers is
required for installation, the included BTLD will also be needed.  To use
the BTLD, enter "link" at the boot prompt and follow the instructions.
Enter the driver name from the list below when prompted for the package name.
If more than one driver is required, use quotes around the names; for example,
"slha wd".
Name      Description
----      ------------------------------
alad      Adaptec 294x (7870 & 7880 Chip)
arad      Adaptec 274x (7770 Chip)
mdac      Mylex Disk Array Controller
slha      Symbios Logic (formerly NCR MPD) 53c8xx Host Adapters
wd        Enhanced IDE, ATAPI Interface (for tapes and CD-ROMs)
PROBLEMS ADDRESSED BY SLS OSS463B
1.      During the installation of SCO OpenServer 5.0.4, if any attempt is
        made to select a SCSI adapter, other than the default for the
        location of the CD-ROM drive, the adapter selection is ignored and
        the CD-ROM is not recognized.  Because of this, it was not possible
        to install from CD-ROMs attached to any SCSI adapter other than the
        default (root drive) SCSI adapter without a boot string.

This replacement N0 diskette includes a new install routine which correctly recognizes the specified CD-ROM SCSI adapter.

2.      The installation fails because the SCSI HBA that is used is not
        supported by the SCO OpenServer 5.0.4 driver.

The replacement N0 and BTLD contain updated alad, arad, mdac, slha and wd drivers.

3.      Choosing the SCSI HBA replacement option during a BTLD installation
        fails if the CD-ROM and root disk drive are not attached to the same
        SCSI adapter.

The replacement N0 diskette contains an updated boot-time linker.

4.      Mounting a secondary IDE hard disk may cause a kernel panic.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 105925. Reproduced with permission. The original is at www.sco.com/ta/105925, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.