Problem
I have learned that an erratum has been identified for the Pentium processor. Is a patch available from SCO to work around the erratum?
Solution
The problem Intel has identified with the Pentium processor
is known as the "Invalid Instruction", or the "f00f" erratum.
Without SLS OSS470A installed on the system the invalid instruction
can freeze the system. This behavior is possible from a user level
program.Note: The Pentium Pro, the Pentium II, and processors prior to the Pentium are not affected by this erratum.
SCO products do not contain the offending instruction so will not
cause the system to freeze in this manner. SCO compilers do not
generate this illegal instruction sequence so a program compiled
using an SCO compiler will not normally generate the offending
instruction sequence. It is possible to manually generate the
instruction sequence within a program.See the attached cover letter that accompanies SLS OSS458A for further information, including installation instructions.
Dear SCO Customer,The enclosed Support Level Supplement (SLS) OSS470A, the Intel Pentium "Invalid Instruction" Erratum Supplement for SCO OpenServer Release 5 corrects a problem in genuine Intel Pentium processors that causes the processor to lock until the system is rebooted.
SLS OSS470A is intended for use on these products:
SCO OpenServer Host System Release 5.0.0, 5.0.2 SCO OpenServer Host System Release 5.0.4 with Release Supplement 504C SCO OpenServer Desktop System Release 5.0.0, 5.0.2 SCO OpenServer Desktop System Release 5.0.4 with Release Supplement 504C SCO OpenServer Enterprise System Release 5.0.0, 5.0.2 SCO OpenServer Enterprise System Release 5.0.4 with Release Supplement 504C SCO Internet FastStart Release 1.0.0, 1.1.0
SLS OSS470A only benefits systems that have a genuine Intel Pentium processor. Intel i386, i486, Pentium Pro, Pentium II, and non-Intel processors do not exhibit this problem.
If you are installing SLS OSS470A on a system with SCO OpenServer Release 5.0.4, the Release Supplement 504C for SCO OpenServer Release 5.0.4 must be installed prior to installing SLS OSS470A.
I. INSTALLING SLS OSS470A1. Prepare the media for installation.Download the OSS470A media image file (oss470a.Z), place the file in the /tmp directory, uncompress and rename the file by typing the following commands:
uncompress /tmp/oss470a.Z
mv /tmp/oss470a /tmp/VOL.000.0002. Run the Software Manager with the command:
# scoadmin softwareor double-click on the Software Manager icon in the desktop.
3. For SCO OpenServer 5.0.4, pull down the "Software" menu and select "Install New".
For SCO Internet FastStart 1.x, and SCO OpenServer 5.0.0 or 5.0.2, pull down the "Software" menu and select "Patch Management --> Apply Patch".
4. When prompted for the host from which to install, choose the local machine and then "Continue".
5. When prompted to select the media device:
If you are installing this SLS from diskette media, select the appropriate floppy disk drive and then "Continue". Proceed to step 6.
If you are installing this SLS from media images per step 1, select
"Media Images", then "Continue". When prompted for the "Image
Directory", enter "/tmp" (or the directory where you placed the VOL
file in step 1) and then select "OK".6. For SCO OpenServer 5.0.4, when prompted to select software to install, ensure that the "OSS470A" entry is highlighted. Choose "Install".
For Internet FastStart 1.x, OpenServer 5.0.0 or 5.0.2, when prompted to select installation type, choose "Full".
7. Once the installation finishes, quit the Software Manager. Installation of SLS OSS470A is now complete. Reboot your system for these changes to take effect.
II. REMOVING SLS OSS470ANote: Patches must be rolled back in the reverse order in which they were installed on a per-component basis. The SLS OSS470A Intel Pentium "Invalid Instruction" Erratum Supplement consists of a patch to the SCO Link kit component in SCO OpenServer 5.0.4, and a patch to the SCO UNIX component in SCO OpenServer 5.0.0 and 5.0.2. If this component was patched after SLS OSS470A was installed, then you will have to roll back the later patch before you can roll back SLS OSS470A.
IIa. Removing SLS OSS470A from SCO OpenServer 5.0.41. Log in as root.2. Execute the command:# scoadmin softwareor double-click on the Software Manager icon in the desktop.
3. Highlight "OSS470A: Intel Pentium 'Invalid Instruction' Erratum Supplement".
4. Pull down the "Software" menu and select "Remove Software".
5. Once the removal finishes, quit the Software Manager. Removal of
SLS OSS470A is now complete. Reboot your system for the removal to
take effect.IIb. Removing SLS OSS470A from SCO OpenServer 5.0.0, 5.0.2 and Internet FastStart 1.0, 1.1
1. Log in as root.2. Execute the command:# scoadmin softwareor double-click on the Software Manager icon in the desktop.
3. SLS OSS470A patches the software component SCO UNIX.
To roll back this patch, pull down the "Software" menu and select "Patch Management-->Rollback Patch".
4. Take these steps:a. You will see the "Begin Rollback Patch" menu and will be asked to select patched software to roll back. Select "SCO UNIX System V Operating System" and choose "Continue".
b. You will see the "Patch Selection" window. Make sure that OSS470A
is selected. Choose "Continue".c. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm the removal of SLS OSS470A.
d. You will see the "Rollback Progress" window, as the system performs the rollback of the patch, and finally a "Rollback Complete" window when the rollback is finished.
7. Exit the Software Manager by choosing "Exit" from the "Host" menu.
Rollback of OSS470A is now complete. Reboot your system for these
changes to take effect.III. PRESERVING CUSTOMIZED FILESSLS OSS470A backs up the following user-configurable file and then replaces it:
/etc/conf/cf.d/vuifileIf you have customized this file, restore your changes from the
backed-up copy after you install SLS OSS470A. The file is backed
up to:/usr/lib/custom/oss470a.sav/etc/conf/cf.d/vuifileIf you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.
We appreciate your business.SCO Support Services