Technical article 105934

What is SLS OSS473A, the SCOterm Security Supplement?

OpenServer 5.0.0OpenServer 5.0.2OpenServer 5.0.4

Written · Last revised

Problem

A vulnerability in /usr/bin/X11/scoterm has been identified. There is a risk that exploit details for this vulnerability which may be distributed.

Solution

Support Level Supplement (SLS) OSS473A, the SCOterm Security Supplement, provides a replacement /usr/bin/X11/scoterm binary for each of the listed SCO operating systems.

See the attached cover letter that accompanies this SLS for more information, including installation instructions.

Dear SCO Customer,

The enclosed Support Level Supplement (SLS) OSS473A, the SCOterm Security Supplement, corrects a vulnerability in the scoterm program.

SLS OSS473A is intended for use on these products:

SCO OpenServer Host System Release 5.0.0, 5.0.2, 5.0.4 SCO OpenServer Desktop System Release 5.0.0, 5.0.2, 5.0.4 SCO OpenServer Enterprise System Release 5.0.0, 5.0.2, 5.0.4 SCO OpenServer Internet FastStart Release 5.0.4 SCO Internet FastStart Release 1.0.0, 1.1.0

Note: SLS OSS473A may be installed on OpenServer Release 5.0.4 either with or without Release Supplement 504C (rs504c) installed on the system.

I. INSTALLING SLS OSS473A
1. Prepare the media for installation.

Download the OSS473A media image file (oss473a.Z file), place the file in the /tmp directory, uncompress and rename the file by typing the following commands:

uncompress /tmp/oss473a.Z
mv /tmp/oss473a /tmp/VOL.000.000

2. Run the Software Manager with the command:

# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. For SCO OpenServer 5.0.4, pull down the "Software" menu and select "Install New".

For SCO Internet FastStart 1.x, and SCO OpenServer 5.0.0 or 5.0.2, pull down the "Software" menu and select "Patch Management --> Apply Patch".

4. When prompted for the host from which to install, choose the local machine and then "Continue".

5. When prompted to select the media device:

If you are installing this SLS from diskette media, select the appropriate floppy disk drive and then "Continue". Proceed to step 6.

If you are installing this SLS from media images per step 1, select
"Media Images", then "Continue".  When prompted for the "Image
Directory", enter "/tmp" (or the directory where you placed the VOL
file in step 1) and then select "OK".

6. For SCO OpenServer 5.0.4, when prompted to select software to install, ensure that the "OSS473A" entry is highlighted. Choose "Install".

For Internet FastStart 1.x, OpenServer 5.0.0 or 5.0.2, when prompted to select installation type, choose "Full".

NOTE: If you have installed the scoterm binary from sse009, you may get a verification error during the installation of OSS473A. If you do, you may safely ignore this error message and continue the installation.

7. Once the installation finishes, quit the Software Manager. Installation of SLS OSS473A is now complete.

II. REMOVING SLS OSS473A
Note: Patches must be rolled back in the reverse order in which they
were installed on a per-component basis.  The OSS473A SCOterm Security
Supplement consists of a patch to the BaseX component.  If this component
was patched after OSS473A was installed, then you will have to roll back
the later patch before you can roll back the SLS OSS473A patch.
IIa. Removing SLS OSS473A from SCO OpenServer 5.0.4
1. Log in as root.
2. Execute the command:
# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. Highlight "OSS473A: SCOterm Security Supplement for SCO OpenServer Release 5".

4. Pull down the "Software" menu and select "Remove Software".

5. Once the removal finishes, quit the Software Manager. Removal of SLS OSS473A is now complete. You must reboot your system for the removal to take effect.

IIb. Removing SLS OSS473A from SCO OpenServer 5.0.0, 5.0.2 and Internet FastStart 1.0, 1.1

1. Log in as root.
2. Execute the command:
# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. SLS OSS473A patches the software component SCO BaseX.  To roll
   back this patch, pull down the "Software" menu and select
   "Patch Management-->Rollback Patch".
4. Take these steps:

a. You will see the "Begin Rollback Patch" menu and will be asked to select patched software to roll back. Select "Standard X Clients" and choose "Continue".

b. You will see the "Patch Selection" window. Make sure that OSS473A is selected. Choose "Continue".

c. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm removal of OSS473A.

d. You will see the "Rollback Progress" window, as the system performs the rollback of the patch, and finally a "Rollback Complete" window when the rollback is finished.

5. Exit the Software Manager by choosing "Exit" from the "Host" menu. Rollback of OSS473A is now complete.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 105934. Reproduced with permission. The original is at www.sco.com/ta/105934, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.