Technical article 109573

What is SLS OSS485A, the Memory Supplement for SCO OpenServer 5.0.4?

OpenServer 5.0.4

Written · Last revised

Problem

My SCO OpenServer Release 5.0.4 system is experiencing a severe degradation in performance, accompanied by the "vhand" process accumulating large amounts of CPU time.

Solution

          Support Level Supplement (SLS) OSS485A, the Memory Supplement,
	  corrects problems in certain system components which can lead
	  to a shortage of low memory.  For more details on the specific
	  problems addressed by this SLS, as well as installation
	  instructions, see the attached cover letter.
Dear SCO Customer,
Support Level Supplement (SLS) OSS485A, the Memory Supplement, corrects
problems in parts of the system which place an excessive demand on low
memory (memory with an address under 16Mb).  See the list below for more
details on specific problems addressed by this SLS.
RELEASE INFORMATION

SLS OSS485A is intended for use on these products:

SCO OpenServer Enterprise System Release 5.0.4 SCO OpenServer Desktop System Release 5.0.4 SCO OpenServer Host System Release 5.0.4

The following supplement MUST be installed prior to installing SLS OSS485A:

SCO OpenServer Release Supplement 5.0.4c (rs504c)
https://ftp.scoexpert.com/Supplements/rs504c/
SLS OSS485A corrects the problems listed below.  In each case, the symptoms
are the same: the system performance severely degrades and the vhand process
is seen, with ps(C) ("ps -p2"), to be using all or most of CPU time.  The
cause is that vhand is looking for low memory which is not available.
1. The High Performance Pipe System was incorrectly allocating low
   memory.  The solution is to allocate non-low memory.

2. Terminal opens were incorrectly allocating low memory.

3. The kernel memory allocator was too readily handing out low memory.

4. The streams buffer allocator was too readily handing out low memory.

NOTE: After installing and/or removing OSS485A according to the
      instructions below, you may receive the following software
      verification errors from the Software Manager:
File "./opt/K/SCO/link/1.1.0Eb/etc/conf/pack.d/kerel/io.a" has size  93182, expe
File "./opt/K/SCO/link/1.1.0Eb/etc/conf/pack.d/kernel/io.a" has checksum 1466176
These errors may be safely ignored.
I. INSTALLING SLS OSS485A
1. Prepare the media for installation.

Download the OSS485A media image file (oss485a file), place the file in the /tmp directory, rename the file by typing the following command:

mv /tmp/oss485a /tmp/VOL.000.000

2. Run the Software Manager with the command:

# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. Pull down the "Software" menu and select "Install New".

4. When prompted for the host to install from, choose the local machine and then "Continue".

5. When prompted to select the media device:

If you are installing this SLS from diskette media, select the appropriate floppy disk drive and then "Continue". Proceed to step 6.

If you are installing this SLS from media images per step 1, select
"Media Images", then "Continue".  When prompted for the "Image
Directory", enter "/tmp" (or the directory where you placed the VOL
file in step 1) and then select "OK".

6. When prompted to select software to install, ensure that the "OSS485A" entry is highlighted. Choose "Install".

7. You will be asked whether or not you want to relink the kernel.

Enter "y" or "n" based on this message. Note that you will not be able to make use of the patch until you relink the kernel. Therefore, it is suggested that you answer "y" to this question.

8. Once the installation finishes, quit the Software Manager.  Installation
   of SLS OSS485A is now complete. The changes will take effect the next
   time you reboot the system.

9. Log in as root on tty01 and shut down the system:

# shutdown -g0 -y

After shutting down and rebooting the machine, application of SLS OSS485A is complete.

II. REMOVING SLS OSS485A

Note: Patches must be rolled back in the reverse order in which they were installed on a per-component basis.

1. Log in as root.
2. Execute the command:
# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. Highlight "OSS485A: OpenServer Memory Supplement."

4. Pull down the "Software" menu and select "Remove Software".

NOTE: There may be "Verification Errors" at this stage because the file
.../io.a has an incorrect checksum.  This warning can safely be ignored.

5. You will be asked whether or not you want to relink the kernel.

Enter "y" or "n" based on this message. Note that package removal
will not take effect until you relink the kernel.  Therefore, it
is suggested that you answer "y" to this question.

6. Once the removal finishes, quit the Software Manager.

7. As root on tty01, shut down the system:

# shutdown -g0 -y

After shutting down and rebooting the machine, removal of this SLS is complete.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 109573. Reproduced with permission. The original is at www.sco.com/ta/109573, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.