Technical article 110943

What is SLS OSS622A, the OpenServer 5.0.5 Replacement Floppy Disk Driver BTLD?

OpenServer 5.0.5

Written · Last revised

Problem

It is not possible to install SCO OpenServer Release 5.0.5 on some
Toshiba portable computers.  When booting from the installation
diskette, the initial boot and hardware summary complete
successfully, but are followed by the error message:
Starting Initial Load from: Floppy Disk
System Error 5
while getting fs type

It is not possible to proceed any further with the installation.

Solution

Support Level Supplement (SLS) OSS622A provides a boot time loadable replacement floppy disk driver to address this problem.

See the attached cover letter for more information, including installation instructions.

Dear SCO Customer,

Support Level Supplement (SLS) OSS622A, the OpenServer 5.0.5 replacement floppy disk driver, allows installation on certain portable computers which otherwise fail to process the boot floppy with the error message:

Starting Initial Load from: Floppy Disk
System Error 5
while getting fs type
The occurs because the SCO OpenServer 5.0.5 floppy driver incorrectly
identifies the floppy diskette controller chip and attempts to enable
a non-existent FIFO.  The driver receives a hard error which causes any
use of the floppy to fail.

SLS OSS622A is a Boot Time Loadable Driver (BTLD) which will replace the standard floppy disk driver with a modified version.

Installation Instructions
-------------------------

To use the replacement floppy disk driver, follow the instructions below.

Format a 3.5" 1.4MB floppy in a system with a working floppy drive:

# format /dev/rfd0135ds18

Download the oss622a.btld.Z image file, uncompress the image and create the BTLD floppy using the dd command:

# uncompress oss622a.btld.Z
# dd if=oss622a.btld of=/dev/rfd0135ds18 bs=18k
To install on a Toshiba portable:

1. Boot the system with the normal OpenServer 5.0.5 Boot Disk, and answer the Boot: prompt as follows:

Boot
: defbootstr link=fd fd.fifo=0

If this fails or if your computer is equipped with a DVD drive, try:

Boot
: defbootstr link=fd fd.fifo=0 wd.noscan

2. When the install boot process prompts you, remove the install floppy from the drive and replace it with the BTLD floppy.

3. The installation process will load the fd driver from the BTLD floppy and will produce a series of messages, culminating in:

Driver <fl> apparently should be replaced with the new driver "fd".
....
Please enter:
        'r' if you wish to try replacement.
        ...

Respond to this by typing 'r' and pressing <Enter>.

4. You will then be prompted:

Driver "fd" will share use of interrupt vector 6 at IPL 5 ...

Please enter:
'0' to replace the handler with "flintr">
...

Respond to this by typing '0'(zero) and pressing <Enter>.

5. Several messages of the following form will now be displayed:

"fd.fd: Characteristic 'O' not supported; ignored"

These are harmless and can be ignored.

6. Then, you will see:

fd: Driver "fd" successfully loaded, ... Insert the Boot disk and press <return>.

Unload the BTLD disk and reinsert the OpenServer 5.0.5 boot floppy.

7. The boot process will continue normally, and the installation process will commence. You will be prompted to reinsert the BTLD disk so that it can later be extracted into the installed link kit in /etc/conf.

You may see messages as follows:

usage: mknod name [ b/c major minor ] [ m/p/s ]

These are harmless and can be ignored.  There is no way to avoid
their output.

8. From this point, the installation continues normally. When installation is completed, you will be asked to reboot the newly installed system. At the Boot prompt for this initial boot, respond:

Boot
: defbootstr fd.fifo=0
or, for systems with DVD drives:
Boot
: defbootstr fd.fifo=0 wd.noscan

9. When the system reboots, edit the defbootstr entry in /etc/default/boot to include "fd.fifo=0". This will then be automatically applied to all subsequent boots.

10. Try mounting the BTLD floppy as a test to assure that the fd driver
    is now properly configured.  With the BTLD disk loaded, type:
# mount /dev/fd0 /mnt

This should succeed with no error messages.

Typing:
# umount /mnt
will then unmount the floppy.
NOTES:    Due to system BIOS incompatibilities, it is not possible to install
          Toshiba portable computers using the bootable CD-ROM feature of SCO
          OpenServer 5.0.5. It is always necessary to start the installation
          by booting from floppy disk.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

From the Xinuos technical article database, record 110943. Reproduced with permission. The original is at www.sco.com/ta/110943, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.