Technical article 117082

What is SLS OSS647A, the Sdsk Supplement for OpenServer Release 5.0.5?

OpenServer 5.0.5

Written · Last revised

Problem

My OpenServer Release 5.0.5 system panics when fsck(ADM) or dosdir(C) is run on several filesystems at the same time.

Solution

Support Level Supplement (SLS) OSS647A corrects panics when several subdivisions (partitions or divisions) of a single hard disk are opened and closed simultaneously.

See the attached cover letter that accompanies this SLS for more information, including installation instructions.

Dear SCO Customer,

Support Level Supplement (SLS) OSS647A, the Sdsk Supplement for OpenServer Release 5.0.5, installs an updated Sdsk driver with the following improvements:

- Corrects a potential panic when a single SCSI disk is simultaneously
  opened and closed by multiple processes.  The OpenServer disk
  partitioning scheme allows a disk to be subdivided into partitions
  and divisions; see hd(HW) for details.  Due to a programming error,
  it was possible for the system to panic if several subdivisions of a
  single disk were opened and/or closed at exactly the same time.
Three specific cases were observed, although others could exist.
The observed cases involved (1) several UNIX filesystems on a single
disk being checked at the same time by fsck(ADM), (2) several Unix
filesystems being created at the same time with mkfs(ADM), and
(3) several DOS filesystems being listed at the same time with
dosdir(C).  The panic occurred in kernel function "dkfree".
- Corrects a potential panic when a certain type of error is returned
  by the SCSI host adapter driver.  This resulted in a panic during
  a restore of a vdisk RAID5 array.  The panic occurred in kernel
  function "Sdsk_setparam".
- Adds the variable Sdsk_set_WCE in /etc/conf/pack.d/Sdsk/space.c.
  When this is set to 1, the driver turns on the WCE (Write-Cache
  Enable) feature of all attached hard disks.  This can improve disk
  writing speed.  When 0, each drive retains its default setting which
  is controlled by the drive's own firmware or the host adapter BIOS.
Software Notes and Recommendations
----------------------------------

SLS OSS647A should only be installed on:

SCO OpenServer Release 5.0.5 with Release Supplement 505A (rs505a) and SLS OSS497C installed.

Note: the multiple open/close problem also existed in SCO OpenServer Release 5.0.6, and was corrected by Release Supplement 506A (rs506a).

Installation Instructions
-------------------------

1. Download the OSS647A media image file (oss647a), place the file in the /tmp directory, and rename the file by typing:

mv /tmp/oss647a /tmp/VOL.000.000

2. Run the Software Manager with the command:

# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. Pull down the "Software" menu and select "Install New".

4. When prompted for the host from which to install, choose the local machine and then "Continue".

5. In the "Select Media" menu, pull down the "Media Device" menu. Select "Media Images", then choose "Continue".

6. When prompted for the "Image Directory", enter "/tmp" (or the directory where you placed the VOL file in step 1) and choose "OK".

7. When prompted to select software to install, make sure that the "OSS647A"
   entry is highlighted.  Choose "Install".
8. Installation of SLS OSS647A is now complete.  To exit the Software Manager,
   select "Exit" from the "Host" menu.
Removal Instructions
--------------------
Patches must be rolled back in the reverse order in which they were installed
on a per-component basis.  That is, if SLS OSS647A is not the most recent patch
applied to the UNIX component of the product, you will have to roll back all
patches applied after SLS OSS647A prior to rollback of SLS OSS647A patch.

To remove SLS OSS647A, take these steps:

1. Log in as root.
2. Execute the command:
# scoadmin software

or double-click on the Software Manager icon in the desktop.

3. Highlight "OSS647A: Sdsk supplement".

4. Pull down the "Software" menu and select "Remove Software".

5. Once the removal finishes, quit the Software Manager.  Removal of
   SLS OSS647A is now complete.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

From the Xinuos technical article database, record 117082. Reproduced with permission. The original is at www.sco.com/ta/117082, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.