Problem
What is Support Level Supplement (SLS) OSS414A and how do I install it?
Solution
The attached cover letter describes the enhancements and corrections to known problems for SCO OpenServer Release 5.0.0 found in, and the installation procedure for, SLS OSS414A.
See also
TA105219, "Can I install SCO Doctor Lite, AFPS or ARCserve/Open Lite from the OpenServer 5.0.2 media onto OpenServer 5.0.0?"
Dear SCO Customer,The enclosed Support Level Supplement (SLS) OSS414A is required before installing the single user/free versions of SCO Advanced File and Print Server Release 3.5.1f, SCO ARCserve/Open Release 2.1.0 and SCO Doctor Release 2.0 on SCO OpenServer Enterprise System Release 5.0.0 or SCO OpenServer Host System Release 5.0.0.
IMPORTANT NOTE: SLS OSS414A is _only_ for SCO OpenServer Enterprise System and SCO OpenServer Host System Release 5.0.0.
If you have SCO OpenServer Enterprise System 5.0.2, SCO OpenServer Host System 5.0.2 or SCO Internet FastStart 1.0.0, you don't need SLS OSS414A.
INSTALLATION AND REMOVAL INSTRUCTIONSInstalling patches on SCO OpenServer 5.0.0 usually consists of two phases:
- "Applying" a patch to a machine results in the problem being corrected on that machine only.
- "Loading" a patch on a machine results in the machine acting as a server to other machines (if they are on the same network) that may need the patch "applied".
I. LOADING THE PATCH1. Log in as root.2. If you are installing this SLS from floppy disk media, skip this step and proceed to step 3.
If you are installing this SLS from a media image, there is a file
called oss414a.Z. Uncompress this file with this command:# uncompress oss414a.ZCopy the file to the /tmp directory and name it VOL.000.000:
# cp oss414a /tmp/VOL.000.0003. Execute the command:# scoadmin softwareor double click on the Software Manager icon on the desktop.
4. Pull down the "Software" menu and select "Patch Management-->Load Patch".
5. You will see the "Begin Load Patch" menu. Be sure the
local machine name is selected and choose "Continue".6. You will see the "Select Media" menu.
a. If you are loading this SLS from floppy disk media, select the appropriate floppy disk drive and choose "Continue". Proceed to step 7.
b. If you are loading this SLS from a media image per step 2, pull
down the "Media Device" menu and select "Media Images", then choose
"Continue". You will then see the "Enter Image Directory" menu.
Enter /tmp and choose "OK".7. You will see the "Load Patch Preference" menu. Choose "Full".8. You will see the "Load Patch Progress" window. If the patch loads
successfully, you will see a "Message" window which states "Load
Patch complete". Choose "OK". You are then returned to the main
Software Manager window.9. To apply the patch now, continue with step 2 under section II,
"Applying the Patch". To exit the Software Manager now, select
"Exit" from the "Host" menu.II. APPLYING THE PATCH1. Log in as root. Execute the command:
# scoadmin softwareor double click on the Software Manager icon on the desktop.
2. Pull down the Software menu and select "Patch Management-->Apply Patch".
3. You will see the "Begin Apply Patch" menu. Be sure that the local
machine name is selected and choose "Continue".4. You will see the "Select Media" menu. The "Hard Disk" menu item
should already be selected. Choose "Continue".5. You will be presented with the "Select Patch-product to Apply" menu. Highlight the SLS OSS414A patch and then choose "Full" to continue.
6. You will see the "Apply Patch Progress" window as the system applies the patch.
7. Then you will see a "Message" window stating "Apply Patch Complete". Choose "OK" and you will be returned to the Software Manager's main menu. Exit the Software Manager by choosing "Exit" from the "Host" menu.
III. NOTES ON NETWORK INSTALLATIONTo install the patch on other SCO OpenServer 5.0.0 machines over the
network, first load the patch as in section I above on a designated
installation server. Then create the user "swadmin" on the installation
server.When running the Software Manager on the system where the patch will be
installed, you will be prompted for the source location of the patch in
the "Begin Load Patch" window. Be sure to choose "From Another Host"
during this phase. You will need to provide the name of the installation
server, as well as the password of the "swadmin" user on the installation
server, to initiate the installation process.IV. PATCH REMOVALNOTE: Patches must be rolled back in the reverse order in which they
were installed on a per-component basis. Hence, if the SLS OSS414A
patch is not the most recent patch applied to the UNIX component of
the product, you will have to rollback all patches applied after the
SLS OSS414A patch prior to rollback of the SLS OSS414A patch.1. Log in as root.2. Execute the command:# scoadmin softwareor double click on the Software Manager icon in the desktop.
3. Pull down the "Software" menu and select "Patch Management-->Rollback Patch".
4. You will see the "Begin Rollback Patch" menu, and be asked to select patched software to rollback. Select "SCO UNIX System V Operating System" and choose "Continue".
5. You will see the "Patch Selection" window. Make sure that the SLS OSS414A patch is selected, and choose "Continue".
6. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm removal of the SLS OSS414A patch.
7. You will see the "Rollback Progress" window, as the system performs the rollback of the patch.
8. Next you will see a "Message" window stating "Rollback Patch Complete".
Choose "OK" and you will be returned to the Software Manager's main
menu. Exit the Software Manager by choosing "Exit" from the "Host" menu.9. To also unload the patch, making it no longer available to be applied,
follow steps 1 through 8 in this section. However, in step 3, choose:"Patch Management-->Unload Patch"instead of:"Patch Management-->Rollback Patch"If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.
We appreciate your business.SCO Support Services