Technical article 104937

What is Support Level Supplement (SLS) OSS422A?

OpenServer 5.0.0

Written · Last revised

Problem

What is Support Level Supplement (SLS) OSS422A and how do I install it?

Solution

The attached cover letter describes the enhancements and corrections to known problems for SCO OpenServer Release 5.0.0 found in, and the installation procedure for, SLS OSS422A.

Dear SCO Customer,

The enclosed Support Level Supplement (SLS) OSS422A, the SCSI Tape Driver Supplement, contains two modifications to the SCSI tape driver in OpenServer 5.0.0. It corrects a problem where the "tape unload" command did not issue a SCSI UNLOAD for the no-rewind device. It also reinstates old semantics for the read filemark ioctl, MT_RFM; these old semantics interpret the 3rd argument to the ioctl call as the number of filemarks to skip. This SLS was created for Sybase SQL Server 10. At this time, the only application known to require these old read filemark semantics reinstating is Sybase SQL Server 10. You should assume that all other applications use the new semantics and will therefore fail if this SLS is applied.

INSTALLATION AND REMOVAL INSTRUCTIONS
Installing patches on SCO OpenServer 5.0.0 usually consists of two phases:
"Loading" and "Applying".  The instructions that follow enable you to
both install the patch from distribution media or media image, as well
as configure the patch to be installed from a remote SCO OpenServer 5.0.0
system over a TCP/IP network.
I. BEFORE LOADING THE PATCH

Use the Software Manager to check which patches are currently on the system. Do not install Support Level Supplement (SLS) OSS422A if the SCO Large Server Supplement is installed on your system.

Ensure that the SCO OpenServer Release Supplement Disk Release 5.0.0d has been installed BEFORE loading and applying this SLS.

More information regarding installation of the Release Supplement may be found on page 32 of the SCO OpenServer Release Notes.

II. LOADING THE PATCH
1. Log in as root.

2. If you are installing this SLS from floppy disk media, skip this step and proceed to step 3.

If you are installing this SLS from a media image, there is a file
called oss422a.Z.  Uncompress this file with this command:
# uncompress oss422a.Z

Copy the file to the /tmp directory and name it VOL.000.000:

# cp oss422a /tmp/VOL.000.000
3. Execute the command:
# scoadmin software

or double click on the Software Manager icon on the desktop.

4. Pull down the "Software" menu and select "Patch Management-->Load Patch".

5. You will see the "Begin Load Patch" menu.  Be sure the
   local machine name is selected and choose "Continue".

6. You will see the "Select Media" menu.

a. If you are loading this SLS from floppy disk media,
   select the appropriate floppy disk drive and
   choose "Continue".  Proceed to step 7.
b. If you are loading this SLS from a media image per step 2,
   pull down the "Media Device" menu and select "Media Images",
   then choose "Continue".  You will then see the "Enter Image
   Directory" menu.  Enter /tmp and choose "OK".
7. You will see the "Load Patch Preference" menu.  Choose "Full".
8. You will see the "Load Patch Progress" window.  If the patch loads
   successfully, you will see a "Message" window which states "Load
   Patch complete".  Choose "OK".  You are then returned to the main
   Software Manager window.
9. To apply the patch now, continue with step 2 under section III,
   "Applying the Patch".  To exit the Software Manager now, select
   "Exit" from the "Host" menu.
III. APPLYING THE PATCH

1. Log in as root. Execute the command:

# scoadmin software

or double click on the Software Manager icon on the desktop.

2. Pull down the Software menu and select "Patch Management-->Apply Patch".

3. You will see the "Begin Apply Patch" menu.  Be sure that the local
   machine name is selected and choose "Continue".
4. You will see the "Select Media" menu. The "Hard Disk" menu item
   should already be selected.  Choose "Continue".

5. You will be presented with the "Select Patch-product to Apply" menu. Highlight the "Tape Driver Supplement" patch and then choose "Full" to continue.

6. You will see the "Apply Patch Progress" window as the system applies the patch.

7. You will see this message:

NOTE: Application or rollback of this patch requires a kernel relink. If you are applying or rolling back several patches at this time, you may choose to defer the relink until the last patch application or rollback. However, you must relink for the system to enable the patch. Do you want to relink the kernel now? (y/n)

Enter "y" or "n" based on this message. Note that you will not be able
to make use of this patch until you relink the kernel.  Therefore, it is
suggested that you answer "y" to this question.
8. If you chose "y" in step 7, the kernel will be relinked.  In either case,
   you will then see:
Press <RETURN> to continue
After pressing <RETURN>, you will see the "Apply Patch Progress"
window, after which you will see a "Message" window stating "Apply
Patch Complete".  Choose "OK" and you will be returned to the Software
Manager's main menu.  Exit the Software Manager by choosing "Exit" from
the "Host" menu.

9. Log in as root on tty01, and shut down the system:

# shutdown -g0 -y

After shutting down and rebooting the machine, application of the patch is complete.

IV. NOTES ON NETWORK INSTALLATION
To install the patch on other SCO OpenServer 5.0.0 machines over the
network, first load the patch as in section II above on a designated
installation server.  Then create the user "swadmin" on the installation
server.
When running the Software Manager on the system where the patch will be
installed, you will be prompted for the source location of the patch in
the "Begin Load Patch" window.  Be sure to choose "From Another Host"
during this phase.  You will need to provide the name of the installation
server, as well as the password of the "swadmin" user on the installation
server, to initiate the installation process.
V. PATCH REMOVAL
 NOTE: Patches must be rolled back in the reverse order in which they
were installed on a per-component basis.  Hence, if the "Tape Driver
Supplement" patch is not the most recent patch applied to the UNIX
component of the product, you will have to rollback all patches applied
after the "Tape Driver Supplement" patch prior to rollback of the "Tape
Driver Supplement" patch.
1. Log in as root.
2. Execute the command:
# scoadmin software

or double click on the Software Manager icon in the desktop.

3. Pull down the "Software" menu and select "Patch Management-->Rollback Patch".

4. You will see the "Begin Rollback Patch" menu, and be asked to select patched software to rollback. Select "SCO UNIX System V Operating System" and choose "Continue".

5. You will see the "Patch Selection" window. Make sure that the "Tape Driver Supplement" patch is selected, and choose "Continue".

6. You will see the "Confirm Selected Patches" window. Choose "Rollback" to confirm removal of the "Tape Driver Supplement" patch.

7. You will see the "Rollback Progress" window, as the system performs the rollback of the patch.

8. You will see this message:

NOTE: Application or rollback of this patch requires a kernel relink. If you are applying or rolling back several patches at this time, you may choose to defer the relink until the last patch application or rollback. Do you want to relink the kernel now? (y/n)

Enter "y" or "n" based on this message. Note that complete rollback of this patch requires a relink of the kernel to be complete. Therefore, it is suggested that you answer "y" to this question, unless you are installing or removing other patches.

9. If you chose "y" in step 8, the kernel will be relinked. In either case, you will then see:

Press <RETURN> to continue

After pressing the <RETURN> key, you will see the "Rollback Progress" window, after which a "Message" window stating "Rollback Patch Complete". Choose "OK" and you will be returned to the Software Manager's main menu. Exit the Software Manager by choosing "Exit" from the "Host" menu.

10. Log in as root on tty01, and shut down the system:

# shutdown -g0 -y

After shutting down and rebooting the machine, rollback of the patch is complete.

11. To also unload the patch, making it no longer available to be applied,
    follow the steps in this section.  In step 3, choose:
"Patch Management-->Unload Patch"
instead of:
"Patch Management-->Rollback Patch"

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 104937. Reproduced with permission. The original is at www.sco.com/ta/104937, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.