Technical article 105646

What is the Release Supplement for SCO OpenServer 5.0.4 (ver 504B), RS504B?

OpenServer 5.0.4

Written · Last revised

Problem

What is contained in Release Supplement RS504B, the second Release Supplement for SCO OpenServer Release 5.0.4?

Solution

The attached cover letter describes the enhancements and corrections to known problems for SCO OpenServer Release 5.0.4 found in, and the installation procedure for, RS504B.

Dear SCO Customer,

The enclosed Release Supplement, the Release Supplement 504B for SCO OpenServer Release 5.0.4, corrects the following problems on an SCO OpenServer Release 5.0.4 system:

o Some system files have improper permissions, which make them vulnerable to possible tampering.

o The Software Manager cannot install products that are packaged as a
  tar(C) archive.

o The Software Manager may terminate ungracefully if a patch installation is attempted to a non-existent or non-installed component.

NOTE: Release Supplement RS504B supersedes Release Supplement RS504A.

WHO SHOULD INSTALL THIS SUPPLEMENT?

This Release Supplement should be installed on all SCO OpenServer 5.0.4 systems, including systems with Release Supplement RS504A previously installed.

BEFORE INSTALLING RS504B
o Remove RS504A, if installed.
If, when invoking the SCO Software Manager (from the graphical desktop or by
typing "scoadmin software" from a character-based session) it shows that the
"Release Supplement for SCO OpenServer Release 5.0.4 (ver rs.Unix504.0.1.a)"
is installed on the system, you should remove that Supplement (RS504A)
before installing RS504B.  See the instructions below for PATCH REMOVAL
in order to remove RS504A.
Please note that the name "RS504A" does not appear in the patch description
shown in the Software Manager.  Use the Patch ID rs.Unix504.0.1.a as evidence
that RS504A is indeed installed.  "(ver rs504b)" will display as part
of the patch description after RS504B is installed.

o If you do not have the XDesktop software component installed, do not install the XDesktop patch contained within RS504B.

To check this, highlight "SCO OpenServer Enterprise System" (or Desktop, Host, or Internet FastStart) in the Software Manager, then expand the view to display the contents of "SCO OpenServer Enterprise System Graphics". You should see "Desktop (ver 3.6.2b)". See the instructions below for more details on omitting the XDesktop patch from the RS504B installation if the XDesktop component is not installed. Should you choose to install the XDesktop component at a later time, the XDesktop patch may be selected from RS504B for installation, using the same steps outlined below.

INSTALLATION AND REMOVAL INSTRUCTIONS

The instructions that follow enable you to either install the patch from distribution media or from a media image.

Note that in pre-5.0.4 releases, the Software Manager "Install" option
was known as the "Apply" option.  The "Apply" terminology has been
replaced by the more intuitive "Install".
I. INSTALLING THE PATCH
1. Log in as root.

2. If you are installing this Release Supplement (RS) from a media image, there is a file called VOL.000.000.

Copy the file to the /tmp directory:

# cp VOL.000.000 /tmp
3. Execute the command:
# scoadmin software

or double click on the Software Manager icon on the desktop.

4. Pull down the "Software" menu and select "Install New".

5. You will see a window pop up asking "What host (machine) do you want
   to install from?"  Choose your own machine and then "Continue".

6. You will see the "Select Media" menu.

a. If you are loading this Release Supplement from a media image per step 2, pull down the "Media Device" menu and select "Media Images", then choose "Continue". (From the desktop you may need to pull down the slider bar before seeing the "Media Image" choice.)

You will then see the "Enter Image Directory" menu.  Enter /tmp
and choose "OK".

b. If you are loading this Supplement from floppy disk media, select the appropriate floppy disk drive and choose "Continue".

7. You will see the "Install Selection on <your hostname>" menu.

a. If you have the XDesktop component installed (which is likely),
   simply choose "Install".  After a short delay, the "Installation
   Complete" pop-up window should appear.  The Software Manager should
   now display the Release Supplement with a full CD to the left of the
   entry.
b. If you do not have the XDesktop component installed (as discussed
   above), highlight "Release Supplement for SCO OpenServer Release 5.0.4
   (ver 504b)" and press <Enter> to expand the view.  Use the space bar
   to select the "Release Supplement for SCO Unix component" and "Release
   Supplement for SCO Software Manager" component, leaving the "Release
   Supplement for SCO XDesktop" component unselected.  Tab down and select
   "Install".  After a short delay, the "Installation Complete" pop-up
   window should appear.

8. Exit the Software Manager by choosing "Exit" from the "Host" menu. The patched software is now installed on the system.

II. PATCH REMOVAL
Note: Patches must be rolled back (removed) in the reverse order in which
they were installed on a per-component basis.  Hence, if the "License
Manager GUI Supplement" patch is not the most recent patch applied to the
UNIX component of the product, you will have to roll back all patches
applied after the "License Manager GUI Supplement" patch prior to rollback
of the "License Manager GUI Supplement" patch.

Note: Unlike pre-5.0.4 OpenServer releases, rolling back a patch ("Remove Software" option) also unloads the patch.

Note: Some effects of this particular patch, RS504B, are irreversible because
of the nature of the correction (restoring correct permissions on system
directories).  However, rolling back the patch will remove the patch name
from the system.  The patch installation order considerations above still
apply to RS504B.
1. Log in as root.
2. Execute the command:
# scoadmin software

or double click on the Software Manager icon in the desktop.

3. Highlight "Release Supplement for SCO OpenServer Release 5.0.4 (ver 504b)" (or the title of the patch you are removing.)

4. Pull down the "Software" menu and select "Remove Software".
   A confirmation window will appear.  Select "Remove".

5. After a few moments, you will see a pop-up window indicating that removal is complete.

6. Exit the Software Manager by choosing "Exit" from the "Host" menu.

III. NOTES ON NETWORK INSTALLATION
To install the patch on other SCO OpenServer 5.0.4 machines over the network,
first use the Software Manager to "Install" or "Load" RS504B on a designated
installation server.  Then create the user "swadmin" on the installation
server.
When running the Software Manager on the system where the patch will be
installed, you will be prompted for the source location of the patch in
the "Begin Load Patch" window.  Be sure to choose "From Another Host"
during this phase.  You will need to provide the name of the installation
server, as well as the password of the "swadmin" user on the installation
server, to initiate the installation process.

If you have questions regarding this Release Supplement, or the product on which it is installed, please contact your software supplier.

We appreciate your business.
SCO Support Services

From the Xinuos technical article database, record 105646. Reproduced with permission. The original is at www.sco.com/ta/105646, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.