Technical article 104926

What is the support status of Tricord machines?

OpenServer 5.0.0

Written · Last revised

Problem

What is the support status of Tricord machines?

Solution

Support of Tricord machines depends on the release or version
of the SCO software.  This section is divided into three sub-
sections:
(A) SCO OpenServer Release 5.0.0 software

(B) SCO UNIX System V/386 Release 3.2 Version 4.x based software

(C) General notes regarding Tricord
(A) SCO OpenServer Release 5.0.0 software
=========================================

Calls on issues involving Tricord drivers such as IIOP, EIOP or ISS SCSI subsystem, or the Symmetrical Multiprocessing (SMP) using the GPI interface structure, should be redirected to Tricord at 1-800-TRICORD.

As of SCO OpenServer Release 5.0.0, with the Advanced Hardware
Supplement (AHS) 5.1, the IIOP and SMP drivers for Tricord are
now incorporated in the SCO distribution.  Therefore, support
would come from SCO.  Note also that now the IIOP actually handles
all three types of Tricord host adapters automatically.  Instead
of using "mkdev hd", there are other Tricord-specific mkdev commands
you must use to configure these.
(B) SCO UNIX System V/386 Release 3.2 Version 4.x based software
================================================================

This includes all software that is SCO UNIX Version 4.x based.

Redirect calls regarding these versions of SCO software on Tricord systems to Tricord at 1-800-TRICORD.

If Tricord's support cannot solve the problem, they escalate
the call to their engineering department.  If their engineering
department cannot solve the problem, they will escalate the call
to SCO's Engineering Services.

"mkdev hd" on a Tricord system actually indirects into some Tricord-supplied utilities for that interface with their SCSI bus. The "mkdev hd" interface may be different than the interface SCO normally provides.

(C) General notes regarding Tricord/SCO
=======================================

When calling regarding Tricord support, it is important to have the serial number of the Tricord machine for Tricord's internal tracking purposes. Also, the firmware levels of the various boards involved, including the BIOS on the motherboard, would be useful. The firmware revision levels are specified at the end of the part numbers of the chipsets for each of the boards; for example, partno-xx, where "xx" is the revision level.

The SCO products offered by Tricord are based on standard
off-the-shelf SCO software.  These special versions of SCO software
are available directly from Tricord and are sold and supported by
Tricord and their resellers.  SCO manufactures these products as a
co-labeled SCO/TRICORD product.  The special Tricord/SCO software
includes:

- A BTLD for their high-performance SCSI host adapters: IIOP, EIOP or ISS.

- An add-on MPX supplement disk.
Some Tricord systems use a hardware-based RAID implementation.
The physical disk layout may or may not correspond to the logical
layout.  In addition, Tricord has their own "Dsk" driver which takes
the place of Sdsk.  This was needed to facilitate their hardware
RAID when the SCO UNIX System V/386 Release 3.2 Version 2.0 was the
current release.
NOTE:     The ES series TRICORD machines use a differential SCSI bus, which
          work with differential SCSI devices.  Installing single-ended
          devices on this bus can cause system corruption.

See also

"SCO UNIX System for TRICORD PowerFrame Supplementary Release Notes" available from Tricord.

From the Xinuos technical article database, record 104926. Reproduced with permission. The original is at www.sco.com/ta/104926, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.