Technical article 105335

Why does my system hang when I install my new Adaptec 2940AU host adapter?

OpenServer 5.0.0OpenServer 5.0.2OpenServer 5.0.4OpenServer 5.0.5OpenServer 5.0.6

Written · Last revised

Problem

I have just installed a new Adaptec AHA-2942AU or AHA-2940AU Host
Adapter card.  Rebooting my system fails with the error message:
Stage 1 Boot Failure

I have adjusted the setting in the host adapter BIOS, disabling Plug-and-Play and DOS Translation.

Beginning with BIOS version 1.21 (other affected versions are
1.30, 1.32, 1.34 or later), I get a PANIC during
the initial system load (ISL) of the operating system or when
I add the controller to an already configured system.  The panic is
"an unexpected kernel k_trap has occured" during the F aladinit stage
of the boot process.

I am using the default "alad" driver supplied with the OpenServer media or using the Adaptec "alad325" version available from:

http://www.adaptec.com

Cause

Adaptec and SCO Engineering are aware of problems with
BIOS version 1.21 of the Adaptec 2940AU card, and are working
to resolve these issues.  These problems have been known to lead
to boot failure.

This controller has been certified with BIOS 1.32.

Solution

The Adaptec 2940AU is known to work on some SCO OpenServer 5.0.x- systems with DOS Translation _enabled_, which is contrary to the usual SCO recommendation for systems with large SCSI hard disks.

More specifically, the card has been known to work normally on a
100 Mhz Pentium single cpu machine with the factory default
settings for a PCI-based system.  These settings are:
Basic Host Adapter Settings
---------------------------
Host Adapter SCSI ID            7
SCSI Parity Checking            Enabled
Host Adapter SCSI Termination   Automatic
Boot Device Settings
--------------------
Boot SCSI ID                    0
Boot LUN Number                 0
SCSI Device Settings
--------------------
Initiate Sync Negotiation       Yes
Enable UltraSCSI Speed          No
Maximum Sync Transfer Rate      10 MBytes/sec
Enable Disconnection            Yes
Send Start Unit SCSI Command    No
BIOS Multiple LUN Support       No
Advanced Host Adapter Settings
------------------------------
Plug and Play SCAM Support      Disabled
Host Adapter BIOS               Enabled
Support Removable Disks Under   Boot only
 BIOS as Fixed Disks
Extended BIOS Translation for   Enabled <--usually Disabled
 DOS Drives >1 GByte                       on SCO systems
Display <Cntl A> Message        Enabled
 During BIOS Initialization
BIOS Support for Bootable       Disabled
 CD-ROM
BIOS Support for Int 13         Enabled
 Extensions

Later BIOS revisions of the card will have an additional option to "Reset SCSI Bus at IC Initiator" and this should be set to "Disabled".

You should then be able to install.

NOTE:     Check here in the future for updated information on drivers and
          improvements as they become available, including specific
          information on the latest BIOS version(s).

This article refers only to the new release AHA-2940AU/AHA-2942AU. Previous editions of the 2940 model have been tested and are listed in the Hardware Compatibility Handbook (HCH) accordingly.

From the Xinuos technical article database, record 105335. Reproduced with permission. The original is at www.sco.com/ta/105335, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.