Problem
A manual bringup outgoing PPP link is set up according to the
instructions given in ta109485, "How to manually configure SCO
PPP for incoming/outgoing connections." When pppattach is used
to bring up the link, it dials, connects, logs in, and then
immediately disconnects. Or, it stays connected but is not able
to communicate with other systems on the Internet. I can connect
to my modem and then dial out and log in without getting
disconnected, so this is not a modem or UUCP problem.How can my system's default route be automatically updated when a manual bringup outgoing PPP link (non-Morning Star PPP) uses dynamically assigned IP addresses?
Solution
You can use the shell script /etc/ppphook.sh to update the default
route. A sample /etc/ppphook.sh that is configured to do this
is attached below.#!/bin/sh
# @(#) ppphook.sh,v 6.1.2.2 1996/01/25 22:33:47 brad Exp
#
# Copyrighted as an unpublished work.
# (c) Copyright 1996 Computer Associates International, Inc.
# All rights reserved.
#
# RESTRICTED RIGHTS
#
# These programs are supplied under a license. They may be used,
# disclosed, and/or copied only as permitted under such license
# agreement. Any copy must contain the above copyright notice and
# this restricted rights notice. Use, copying, and/or disclosure
# of the programs is strictly prohibited unless otherwise provided
# in the license agreement.
## This script is called from pppd with the following arguments when a link
# goes up or down: event ifname old_src old_dst new_src new_dst
#
# Where event is "up", "down", "add", or "delete", ifname is the interface
# name, and the remaining 4 arguments are the old and new IP addresses
# in dotted decimal notation.
#
# This is a general example shell script which will rewrite static routes
# to the interface if the address changes. Note that pppd will wait for
# this script to complete before continuing.
#
loglevel=debugif [ $# -lt 6 ] then logger -t ppphook.sh -p $loglevel "wrong number of arguments" exit 1; fi
event=$1; ifname=$2; old_src=$3; old_dst=$4; new_src=$5; new_dst=$6#logger -t ppphook.sh -p $loglevel "interface $ifname $event $3 $4 $5 $6"case $event in down)
logger -t ppphook.sh -p $loglevel "down"
route delete default
if [ -x /etc/rc2.d/S99route ]
then
sh /etc/rc2.d/S99route
fi
exit 0;;
add)
logger -t ppphook.sh -p $loglevel "add"
if netstat -rn | grep "^default"
then
route delete default
fi
route add default $5 | logger -t ppphook.sh -p $loglevel
exit 0;;
up|delete)
echo "$old_src vs $new_src" | logger -t ppphook.sh -p $loglevel
if [ "$old_src" != "$new_src" ]
then
# change static ("S") routes which point to old_src and ifname
netstat -rn | awk '
$6 == "'$ifname'" && $2 == "'$old_src'" && index($3, "S") \
{ print "route change " $1 " '$new_src'" }' |
sh | logger -t ppphook.sh -p $loglevel
echo route delete default | sh | logger -t ppphook.sh -p $loglevel
echo route add default $6 | sh | logger -t ppphook.sh -p $loglevel
fi
if [ "$event" = "delete" ]
then
route delete default
if [ -x /etc/rc2.d/S99route ]
then
/etc/rc2.d/S99route
fi
fi
exit 0;;
*)
logger -t ppphook.sh -p $loglevel "unknown event: $event"
exit 1;;
esac
exit 2NOTE: The ppphook.sh shell script in this Technical Article was kindly
submitted by Barry Sandever of ISIS Incorporated. See also
ta109485, "How to manually configure SCO PPP for incoming/outgoing connections."
ta107563, "How to configure an outgoing PPP connection with IP address negotiation."
ta105903 "How do I configure my 5.0.x server as a gateway?"
ta107704 "What is SLS OSS449F Network Maintenance Supplement?"