Problem
How can I install OpenServer 5.0.7 on the ASUS F8SN Laptop?
HARDWARE: The hardware configuration of the ASUS F8Series (F8SN) this article was tested with is:
CPU: Intel Core 2 Duo T9300 on an Intel 965PM motherboard RAM: 3GB Hardisk: Samsung HM160HI SATA 160GB (or alternatively with a Hitachi 250GB SATA disk) Graphic card: nVIDIA GeForce 9500M GS with 512 MB VRAM Network Card: Realtek Gbit Network card RTL (8168B) BIOS: AMIBIOS Version 302 or later
Solution
Before you install:
------------------
1) OpenServer 5.0.7 does not support S-ATA in enhanced
mode with the onboard S-ATA controller available in this
machine.You will need to enter the BIOS (Press F2 during system start), change to the "Advanced Menu" Tab -> "IDE Configuration" and change the SATA Operation Mode from "Enhanced" to "Compatible".
2) You need to follow TA126828 in order to create a BTLD BOOT CD with an updated wd driver.
The wd driver that is included in the OpenServer 5.0.7 installation CD image does not detect the disk controller. We have done this for you and you can download the ISO image from (state 20.07.2008) osr507boot-CD-wd-v3.iso
This can be downloaded from:ftp://ftpput.sco.com/tmp/osr507boot-CD-wd-v3.iso3) You will need to disable the USB subsystem during installation since the USB implementation that ships with OpenServer 5.0.7 is incompatible and will result in a PANIC during installation. (see TA127056).
The ASUS F8Series BIOS has a "Security -> I/O Subsystem Security Menu" that allows to "LOCK" the USB components. Setting "LOCK" will disable all USB devices. (The BIOS Default is UNLOCKED)
We will re-enable USB after we have the system installed and the latest Maintenance Pack applied.
Installation:
------------
You need both the BTLD Boot CD with the new "wd" BTLD and
the July 2005 cut of SCO OpenServer 5.0.7 install CD.Boot the server with the BTLD Boot CD. At the boot prompt, type "dir" to check if "wd" is there.
boot
: dirNow add the following install boot string:
boot
: defbootstr link=fd(64)wd <RETURN>Please Note:"link=fd(64)wd" is equvilant to "link=wd btld=fd(64)"At the message below, just hit the <RETURN>Please insert the fd(64)wd volume and press <Return> or 'q' to quit: <RETURN>
The boot sequence will then load the "wd" BTLD from the BTLD Boot CD and you will notice that the "wd" was successfully loaded and linked to the install Kernel.
Continue the installation and confirm with OK on the screen message:
Please insert (wd) package BTLD disk into the floppy drive so that it can be extracted onto the hard disk for incorporation into the link-kit.
at the "Media device to be used" screen, remove the BTLD Boot CD and insert the SCO OpenServer 5.0.7 Install CD.
Regardless of any further suggestions, there will be no need to insert the new BTLD Boot CD again.
Continue the installation with keyboard, license and disk configuration....etc
Network:
--------
When you are prompted to configure the Network Card choose:"Defer" as the Realtek network card is not supported by the OpenServer 5.0.7 Installation CD.
We will configure the Realtek card once installation is complete.
Graphical Login:
---------------
When you are prompted for the video configuration, choose:VESA SVGA (default), press the space key and set Graphical login to : scologin off.
After the latest Maintenance Pack later on has been installed, we will enable scologin.
Mouse:
-----
Choose Low resolution keyboard Mouse. If you use an
external USB mouse, you need to use the "mkdev mouse"
command, after Openserver 5.0.7 and the latest Maintenance
Pack has been installed and USB has been UNLOCKED then in the BIOS.When the installation gets to the point where it wants to load "wd" BTLD into link-kit, you will then get this error message:
The BTLD package will now be extractedmount: Bad addressPlease select the floppy device you are using(1) /dev/fd0
(2) /dev/fd1choose option (2) and you will be asked to insert the wd BTLD floppy disk again:
Please insert the floppy for BTLD package: wd and press <Return>:
Press RETURN and you will then get this message:
mount: Bad address, Could not mount the BTLD floppyYou may:(a) try again (b) abort BTLD load, but continue installation (c) abort the installation
Respond with one of (a,b,c):choose option "b".We will later load the wd BTLD into the link-kit at the post installation.
The installation will continue and OpenServer 5.0.7 will get installed on to the Hard Drive.
Please Note:The finished installed OpenServer 5.0.7 kernel will not have the "wd" BTLD linked to it. So if you now try to reboot, OSR507 will fail to boot from the HD.
POST Installation:
-----------------
When the installation has finished, remove the SCO OpenServer 5.0.7
Install CD and insert the BTLD Boot CD again and reboot the server.At the Boot prompt, enter either one of the following boot string:
boot
: defbootstr link=fd(64)wd root=hd(42) Srom=wd(0,0,0,0)Boot using the install unix kernel on the BTLD Boot CD (OSR507 install kernel), bind the wd to the install kernel, CD-ROM drive attached to PRIM IDE controller as the master and use the root filesystem on the Hard Drive hd(42) as the landing level (OSr507) is already installed on the hard drive).
Please Note: The Srom in the boot string is VERY important
to to add. Failing to add it, will result in
failure accessing the CD-ROM device /dev/cd0.Or:boot
: link=fd(64)wd hd(40)unix.install root=hd(42) Srom=wd(0,0,0,0)Same as above but using the unix.install kernel on the hard drive hd (40) instead.
Please Note: If you use the regular unix kernel (unix / unix.old or even unix.safe), which all reside in /stand filesystem, you will get this message:
bootlocore: Out of low (below 1Mb) memory!
No memory for string table
No (or cannot load) kernel hd(40)unix symbol
table Link failed, press <Return> to continue
or q to quit:This is because the regular unix kernel is fully linked and you won't have enough memory.
Therefore, we use "unix.install", as it will fit in the memory.
Continue as before and hit RETURN at the message:
Please insert the fd(64)wd volume and press <Return> or 'q' to quit: <RETURN>
to load the "wd" BTLD.At the INIT: SINGLE USER MODE, enter the root password to enter into system maintenance mode.
Mount the BTLD Boot CD and install the "wd" BTLD:
# mount /dev/cd0 /mnt
# mkdir /mnt2
# marry -a /mnt/osr507boot-CD.img
# mount -r /dev/marry/mnt/osr507boot-CD.img /mnt2
# btldinstall /mnt2You will be given the wd BTLD on the list.
Press RETURN to choose the default "wd".
The BTLD wd gets loaded and then OpenServer 5.0.7 will tell you that the "wd" is already installed and you are requested to proceed with "y" to install and over write the old "wd" driver or "n" for NO and exit.
Proceed with "y" to update the "wd" driver and then "y" to relink the kernel.
If you are not asked to build the kernel, run:
# /etc/conf/cf.d/link_unix -yUn-marry and unmount the BTLD Boot CD and reboot:
# umount /mnt2
# marry -d /dev/marry/mnt/osr507boot-CD.img
# umount /mnt
# init 6SCO OpenServer 5.0.7 is now installed on a machine where a BTLD was loaded via CD-ROM during installation on a machine with no Legacy Floppy drive or USB floppy drive.
SMP software installation:
-------------------------
This machine is using a Core 2 Duo processor. In order to
utilize both Cores you need to install the SMP software
from the OpenServer 5.0.7 installation CD. (before
installing a Maintenance Pack)You do not need to license the second core, hence while being asked for a license during SMP installation, simply choose DEFER.
Maintenance Pack installation:
-----------------------------
Now install the latest Maintenance Pack. (MP5 at the time
of writing).This is a prerequiste before you can enable USB in the BIOS again.
Network card:
------------
Download the driver for the Realtek network card from:http://www.realtek.com.tw/Look for the RTL8111B/RTL8168B/RTL8111/RTL8168/RTL8111C
Software Download.At the time of this writing this has been version 1.0.4 from 28.04.2008
Use custom to install the files.(you need to unpack them first and might need to rename a file like GBE.vol into VOL.000.000 and then use custom to install from media images)
Run netconfig and add the new adapter. You need to scroll down in the list of adapters and choose:
"Realtek RTL8169/8168/8110 Family Gigabit PCI Adapter"Configure TCP/IP and then relink and reboot.
Enable USB:
----------
Enter the BIOS and enable USB in the I/O Security menu. USB Mouse:
---------
Use mkdev mouse if you want to configure a USB mouse.Enable scologin, if required:
----------------------------
Use "scologin enable" in order to enable the graphical
login. This will work now with the Maintenance Pack applied.