Technical article 105584

How do I install Internet FastStart on the Compaq ProLiant 2500 using a SMART 2/P or 2/E Array controller?

OpenServer 5.0.2

Written · Last revised

Problem

What is the procedure to correctly install SCO Internet FastStart on the ProLiant 2500 using a SMART Array Controller?

Solution

Although there may be slight variations in the flow of this
procedure based on how you respond to prompts, the process will
generally be as follows.  It will be necessary to obtain Support
Level Supplement (SLS) OSS451B from the /SLS subdirectory on the
SCO FTP site. This supplement provides a new 'wd' driver which
will be linked into the kernel during the installation.
Boot the server from the Compaq replacement N1 Boot Floppy provided
in the latest Compaq EFS diskette set.  To obtain the latest Compaq
EFS, see the article, "How do I obtain the Compaq Extended Feature
Supplement (EFS) 5.xx?".

For a first time installation, in response to the Boot: prompt, type 'link', as follows:

SCO OpenServer(TM) Release 5
Boot
: link

You will then be prompted for which packages you want to link into the kernel.

What packages do you need linked in the system, or q to quit?: wd ida cha

You will see:

fd(64)unix root=ram(7) ram.preload=7 swap=none dump=none nbuf=100 ramdisk=fd(64) rootFS link="wd ida cha" btld=fd(60)

Sizing memory
................
Loading kernel fd(64)unix .text
.....................................
Loading kernel fd(64)unix .data
.....................................
Loading kernel fd(64)unix .bss

Loading kernel symbol table, this may take a few minutes

Please insert the fd(60)wd volume and press <Return>, or 'q' to quit.

At this point, insert the BTLD diskette from SLS OSS451B, then
press <Enter>.  You will see:
wd.wd Loading module fd(60)/wd/driver/wd/Driver.o .text
..............
wd.wd Loading module fd(60)/wd/driver/wd/Driver.o .data
..
wd.wd Loading module fd(60)/wd/driver/wd/Space.o .text
.
wd.wd Loading module fd(60)/wd/driver/wd/Space.o .data
.
wd.wd Driver <wd> occupies block and character major 53
Driver <wd> should apparently be replaced with
the new driver "wd".  Replacing a driver may
result in a kernel which does not work.
You will then see a message and prompt to which you must
reply 'r' to replace.  For example:

Please enter: 'r' If you wish to try replacement, 'a' If you wish to use block and character major 6 [default], which block and character major (0-100) to use ('?' to list), or 'q' to quit?: r

You will then see:
wd: Driver "wd" successfully loaded
    Block major        = 53
    Character major    = 53

Please insert the fd(60)ida volume and press <Return>, or 'q' to quit.

At this point, insert the BTLD diskette from EFS 5.12 or later.
Then press <Enter>.  Eventually, you will see:
ADD HERE:
ADD HERE:
     ida.ida: Loading module fd(60)/CUIDA/driver/ida/Driver.o .text
     ................
     ida.ida: Loading module fd(60)/CUIDA/driver/ida/Driver.o .data
     ...
     ida.ida: Loading module fd(60)/CUIDA/driver/ida/Space.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/ida/Space.o .data
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida0/Driver.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida0/Driver.o .data
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida1/Driver.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida1/Driver.o .data
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida2/Driver.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida2/Driver.o .data
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida3/Driver.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida3/Driver.o .data
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida4/Driver.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida4/Driver.o .data
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida5/Driver.o .text
     .
     ida.ida: Loading module fd(60)/CUIDA/driver/../ida5/Driver.o .data
     .
     Table "io_init" contains (at 38) another routine named "idainit".
You will then see a message and prompt to which you must
reply 'n'.  For example:

Please enter which routine (0-38) to replace ('?' to list), 'a' to add "idainit" to the end [default], 'n' to do nothing, or 'q' to quit: n

You will then see:
ida: Driver "ida" successfully loaded.

Please insert the fd(60)cha volume and press <Return>, or 'q' to quit.

The same EFS floppy used for the 'ida' driver above, contains the
'cha' driver.  Simply press <Enter>.  The following screen of
information will appear:
cha.cha: Loading module fd(60)/CUCHA/driver/cha/Driver.o  .text
...................................................................
cha.cha: Loading module fd(60)/CUCHA/driver/cha/Driver.o  .data
..........................
cha.cha: Loading module fd(60)/CUCHA/driver/cha/Space.o  .data
.

cha: Driver "cha" successfully loaded. Character major = 6

Insert the Original SCO Boot Disk and press <Return>.

At this point, insert the original SCO Internet FastStart Boot Floppy which came with your CD-ROM media from SCO and press <Enter>.

Eventually you will be prompted to insert the 'wd' BTLD disk.
Insert the SLS OSS451B BTLD floppy to be incorporated onto the
hard disk into the link-kit. Press <Enter>.  You should see a
blue " RESTRICTED RIGHTS LEGEND" screen.

Proceed to the "Identifying the installation media device" screen. Press the space bar to toggle to SCSI CD-ROM from SCSI Tape.

Media device to be used: SCSI CD ROM
SCSI Adapter Type:     wd
SCSI Host adapter:     0
SCSI ID:               0
SCSI LUN:              0
SCSI BUS:              0

Note, the above settings indicate that the CD-ROM is the master device on the primary IDE Controller.

Insert the CD-ROM media when prompted.

After entering the licensing information, select the configuration parameters appropriate for your installation.

To preserve the EISA Configuration Utility (ECU) partition that we recommend you install prior to installing the operating system, it is necessary to perform an "Interactive fdisk/divvy" installation.

When prompted for the networking configuration, choose to 'defer' networking if you are using the integrated NIC. For additional information regarding configuring the integrated NIC, see TA105479, "My Netelligent NIC is not being recognized during a 5.0.x installation on my Compaq ProLiant.".

As the system installation proceeds, you may see the following:

Preparing root filesystem ... Done.

The BTLD packages will now be extracted.

Extracting BTLD distribution for wd ... Done.

Please select the floppy device that you are using: (1) /dev/fd0 (2) /dev/fd1

Select the appropriate floppy drive.

Please insert the floppy for BTLD package: ida and press <ENTER>:

Insert the EFS BTLD floppy.

Extracting BTLD distribution for ida ... Done.

Several additional messages will appear on the screen during the installation process, including the 'Percent Installation Complete'. Eventually, you will see:

The following verify errors have occurred for software SCO:Unix (ver rs.4.0.a):

File "./opt/K/SSCO/Unix/5.0.2Dp/etc/badtrk" has size 95804, expected 81072
File "./opt/K/SSCO/Unix/5.0.2Dp/etc/badtrk" has checksum 424977648, expected
1373203778
Please enter one of the following:
  'i'  To ignore the error, and continue
  'ca' To cancel
  'cc' To cancel for the current component
Enter choice:

Select 'i', to ignore the error message.

After several additional messages appear on the screen, you will see:

Installation and initial configuration of SCO Internet FastStart is complete.

Before you use the system:

-- Perform any additional configuration needed, as described in the Release Notes.

-- Create an emergency root and boot floppy set as described in the SCO OpenServer Handbook.

(EOF)
Press <Enter> to continue:
After pressing enter, you will see:
At the "Power Off or Reboot" prompt, remove the floppy disk
from the drive and press any key to reboot.  The screen clears,
then displays the "Boot:" prompt.
**     Safe to Power Off     **
            -or-
**  Press any Key to Reboot  **
Remove the media and press <Enter>.

From the Xinuos technical article database, record 105584. Reproduced with permission. The original is at www.sco.com/ta/105584, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.