Technical article 105485

How do I install OpenServer 5.0.2 on the Compaq ProLiant 2500 using the integrated SCSI controller?

OpenServer 5.0.2

Written · Last revised

Problem

What is the procedure to correctly install SCO OpenServer 5.0.2 on the ProLiant 2500?

Solution

Although there may be slight variations in the flow of this
procedure based on how you respond to prompts, the process will
generally be as follows.  It will be necessary to obtain the
OSS451b supplement from the /SLS subdirectory on the SCO FTP site.
This supplement provides a new 'wd' driver which will be linked into
the kernel during the installation.

Boot the server from the SCO Boot Floppy.

For a first time installation, in response to the Boot: prompt, type 'link' as follows:

SCO OpenServer(TM) Release 5
Boot
: link

You will then be prompted for which packages you want to link into the kernel.

What packages do you need linked in the system, or q to quit?: wd cha

It would also be correct to respond as follows:

What packages do you need linked in the system, or q to quit?: wd CUCHA

You will see:

fd(64)unix root=ram(7) ram.preload=7 swap=none dump=none nbuf=100 ramdisk=fd(64) rootFS link="wd cha" btld=fd(60)

or

fd(64)unix root=ram(7) ram.preload=7 swap=none dump=none nbuf=100 ramdisk=fd(64) rootFS link="wd CUCHA" btld=fd(60)

Sizing memory
................
Loading kernel fd(64)unix .text
.....................................
Loading kernel fd(64)unix .data
.....................................
Loading kernel fd(64)unix .bss

Loading kernel symbol table, this may take a few minutes

Please insert the fd(60)wd volume and press <Return>, or 'q' to quit.

At this point, insert the BTLD diskette from SLS OSS451b, then
press <Enter>.  You will see:
wd.wd Loading module fd(60)/wd/driver/wd/Driver.o .text
..............
wd.wd Loading module fd(60)/wd/driver/wd/Driver.o .data
..
wd.wd Loading module fd(60)/wd/driver/wd/Space.o .text
.
wd.wd Loading module fd(60)/wd/driver/wd/Space.o .data
.
wd.wd Driver <wd> occupies block and character major 53
Driver <wd> should apparently be replaced with
the new driver "wd".  Replacing a driver may
result in a kernel which doe not work.
You will then see a message and prompt to which you must
reply 'r' to replace.  For example:

Please enter: 'r' If you wish to try replacement, 'a' If you wish to use block and character major 6 [default], which block and character major (0-100) to use ('?' to list), or 'q' to quit?: r

You will then see:
wd: Driver "wd" successfully loaded
    Block major        = 53
    Character major    = 53

Please insert the fd(60)cha volume and press <Return>, or 'q' to quit.

At this point, insert the BTLD diskette from EFS 5.12 or later.
Then press <Enter>.  Eventually, you will see:
Insert the Boot Disk and press <Return>

At this point, insert the original SCO OpenServer Release 5 "N0" Boot floppy which came with your CD-ROM media from SCO and press <Enter>.

Eventually you will see the "RESTRICTED RIGHTS LEGEND" screen.

Proceed to the "Identifying the installation media device" screen. Press the space bar to toggle to SCSI CD-ROM from SCSI Tape.

Media device to be used: SCSI CD-ROM
SCSI Adapter Type:     wd
SCSI Host adapter:     0
SCSI ID:               0
SCSI LUN:              0
SCSI BUS:              0

Note: The above settings indicate that the CD-ROM is the master device on the primary IDE Controller.

Insert the CD-ROM media when prompted.
After entering the licensing information, select your configuration
parameters.  When prompted for the networking configuration, choose
to 'defer' networking if you are using the integrated NIC.  For
additional information regarding configuring the integrated NIC,
see TA105479, "My Netelligent NIC is not being recognized during
a 5.0.x installation on my Compaq ProLiant".

As the system installation proceeds, you may see the following:

Preparing root filesystem ... Done.

The BTLD packages will now be extracted.

Extracting BTLD distribution for cha ... Done.

Please select the floppy device that you are using: (1) /dev/fd0 (2) /dev/fd1

Select the appropriate floppy drive.

Please insert the floppy for BTLD package: wd and press <ENTER>:

Insert the SLS OSS451b BTLD Floppy to be incorporated onto the
hard disk into the Link kit. Press <Enter>.  Next, you should
see:

Extracting BTLD distribution for wd ... Done.

Several additional messages will appear on the screen during the installation process, including the 'Percent Installation Complete'. Eventually, you will see:

NOTE: A new kernel must be built for the changes to take effect.

Press return to continue:

After pressing <Enter>, the 'Percent Installation Complete' screen will reappear, and the installation will continue.

Installation of software patches from distribution media will now begin.

After several additional messages appear on the screen, you will see:

Installation and initial configuration of SCO OpenServer Enterprise System is Complete.

Before you use the system:

-- Perform any additional configuration needed, as described in the Release Notes.

-- Create an emergency root and boot floppy set as described in the SCO OpenServer Handbook.

(EOF)
Press <Enter> to continue:
After pressing <Enter>:
At the "Power Off or Reboot" prompt, remove the floppy disk
from the drive and press any key to reboot.  The screen clears,
then displays the "Boot:" prompt.
**     Safe to Power Off     **
            -or-
**  Press any Key to Reboot  **

Remove the media and press the any key.

From the Xinuos technical article database, record 105485. Reproduced with permission. The original is at www.sco.com/ta/105485, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.