Technical article 105644

How do I install OpenServer 5.0.4 on the Compaq ProLiant 2500 or 800 using the integrated SCSI controller for my hard drive(s) and an IDE CD-ROM?

OpenServer 5.0.4

Written · Last revised

Problem

What is the procedure to correctly install SCO OpenServer 5.0.4 on the ProLiant 2500 or 800?

Solution

Although there may be slight variations in the flow of this procedure based on how you respond to prompts, the process will generally be as follows.

Boot the server from the SCO Boot Floppy.

For a first time installation, in response to the Boot: prompt, type the following boot string:

SCO OpenServer(TM) Release 5
Boot
:defbootstr Srom=wd(0,0,0,0) link=cha

Note: The 'wd' portion of the line: (0,0,0,0) indicates that the IDE CD-ROM is configured as the master device on the primary IDE controller.

You will see:

fd(64)unix root=ram(7) ram.preload=7 swap=none dump=none nbuf=100 ramdisk=fd(64) rootFS link="cha" btld=fd(60)

Sizing memory
................
Loading kernel fd(64)unix .text
.....................................
Loading kernel fd(64)unix .data
.....................................
Loading kernel fd(64)unix .bss

Loading kernel symbol table, this may take a few minutes

Please insert the fd(60)cha volume and press <Return>, or 'q' to quit.

At this point, insert the BTLD diskette from EFS 5.14 or later.
Then press <Enter>.  Eventually, you will see:
Insert the Boot Disk and press <Return>

At this point, insert the original SCO OpenServer Release 5 "N0" Boot floppy which came with your CD-ROM media from SCO and press <Enter>.

You will then see the hardware boot screen, and you want to verify
that the CD-ROM is recognized on the IDE controller.  It should be
similar to the following:
%cd-rom         -       -       - type =IDE ctlr=pri cfg=mst dvr=Srom->wd

Press <Enter> to begin the installation at the prompt.

You will again be prompted to insert the 'cha' btld. Insert the
floppy and press <Enter>. Next you will see the "RESTRICTED RIGHTS
LEGEND" screen.  Press <Enter> to continue.

Proceed to the "Identifying the installation media device" screen. Verify that the screen appears as follows:

Media device to be used: IDE CD ROM
IDE Controller:         Primary
Master or Slave:        Master

Note: The above settings indicate that the CD-ROM is the master device on the primary IDE Controller.

Insert the CD-ROM media when prompted.
Respond to subsequent prompts according to your specific
configuration needs.  Enter the appropriate licensing information.

After entering the licensing information, you will be prompted for what type of a installation you are performing on a "Suitability for automatic Upgrade" screen.

Highlight "Fresh" and press <Enter>.  Select "OK" to continue.

Respond to subsequent prompts according to your specific configuration needs.

          When prompted for the networking configuration, choose to "defer"
          networking if you are using the integrated NIC.  For additional
          information regarding configuring the integrated NIC, see
TA105479,           "My Netelligent NIC is not being recognized during a 5.0.x
          installation on my Compaq ProLiant".

Several additional messages will appear on the screen during the installation process, including the "Percent Installation Complete". Eventually, you will see:

After pressing <Enter>, the "Percent Installation Complete" screen will reappear, and the installation will continue.

After several additional messages appear on the screen, you will see:

Installation and initial configuration of SCO OpenServer Enterprise System is Complete.

Before you use the system:

-- Perform any additional configuration needed, as described in the Release Notes.

-- Create an emergency root and boot floppy set as described in the SCO OpenServer Handbook.

(EOF)
Press <Enter> to continue:
After pressing <Enter>:
At the "Power Off or Reboot" prompt, remove the floppy disk
from the drive and press any key to reboot.  The screen clears,
then displays the "Boot:" prompt.
**     Safe to Power Off     **
            -or-
**  Press any Key to Reboot  **

Remove the media and press any key.

From the Xinuos technical article database, record 105644. Reproduced with permission. The original is at www.sco.com/ta/105644, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.