Technical article 109725

How do I install SCO OpenServer 5.0.4, 5.0.5, or 5.0.6 on a Dell PowerEdge 6300?

OpenServer 5.0.4OpenServer 5.0.5OpenServer 5.0.6

Written · Last revised

Problem

My system console goes blank when trying to install SCO OpenServer Release 5.0.4, 5.0.5, or 5.0.6 on a Dell PowerEdge 6300.

Cause

There are some built-in drivers on the installation diskette that don't work with the Dell PowerEdge 6300. Therefore, it hangs while the system console is stuck in reset mode.

Solution

You need to disable some drivers from the installation disk at boot-up time.

For OpenServer 5.0.4 and 5.0.5, the recommended boot string is:

Boot:
defbootstr link=<btld_driver> disable=dptr,piiop,efp,wdex

For OpenServer 5.0.6, the recommended boot string is:

Boot:
defbootstr link=<btld_driver> disable=dptr,piiop,efp,wdex,mdac

where <btld_driver> depends on which SCSI controller is being used.

Note: Standard configuration for the Dell PowerEdge 6300 typically
includes an AIC-7860 chipset and an attached SCSI CD-ROM drive.  Since
it has been observed in some cases that the above bootstrings are not
sufficient for avoiding blank screens and hangs during bootup, it
might then be necessary to append "Srom=alad(0,5,0)" to the bootstring
in order to get the system to boot successfully.
If using an AIC-7890 Adaptec Chipset, then "blad325" should be
the specified "btld_driver" in the above bootstrings.  This driver
can be obtained from Adaptec's Website.

Under OpenServer 5.0.5 and 5.0.6, the "blad" driver is included so the link option ("link=...) is not required.

If using a DELL-RAID SCSI controller, then "perc" should be
the specified driver.  This driver can be obtained directly from
Dell.

For multiprocessor support, here is a list of recommended supplements for the various releases of SCO OpenServer:

On OpenServer 5.0.4:
--------------------

The correct order of the installation is: - Install SCO OpenServer 5.0.4. - Install Symmetrical Multiprocessing (SMP); do not reboot. - Install Release Supplement 504C (rs504c); do not reboot. - Install SLS OSS469D; you can now reboot.

On OpenServer 5.0.5:
--------------------

The correct order of the installation is: - Install SCO OpenServer 5.0.5. - Install Symmetrical Multiprocessing (SMP). - Install Release Supplement 505A (rs505a). - Install SLS OSS497C.

On OpenServer 5.0.6:
--------------------

The correct order of the installation is: - Install SCO OpenServer 5.0.6. - Install Symmetrical Multiprocessing (SMP). - Install Release Supplement 506A (rs506a).

NOTE:     If the Release Supplement has been installed prior to SMP it is
          recommended to boot the server into Single User Mode, remove the
          patches and Release Supplement (all components, ie including the
          Software Manager) then add SMP and license.  After a reboot, back into
          Single User Mode restore the Release Supplement and patches has per
          the installation documentation.

See also

ta109975, "What is SLS OSS469D, the Core OS and Networking Supplement for SCO OpenServer Release 5.0.4?"

ta105811, "What is the Release Supplement 504C for SCO OpenServer Release 5.0.4 (rs504c) and how can I obtain it?"

ta108858, "The shutdown(ADM) and init(M) commands do not work after installing Release Supplement 504C."

ta109909, "What is Release Supplement 505A for SCO OpenServer Release 5.0.5?"

ta110105, "What problems are addressed by SLS OSS497C, the Core OS Supplement for SCO OpenServer Release 5.0.5?"

From the Xinuos technical article database, record 109725. Reproduced with permission. The original is at www.sco.com/ta/109725, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.