Technical article 111072

How do I install SCO OpenServer Enterprise 5.0.x on Compaq systems using the Latest Compaq Smart Array Controllers?

OpenServer 5.0.5OpenServer 5.0.6OpenServer 5.0.7

Written · Last revised

Problem

What is the procedure to install SCO OpenServer Enterprise on the ProLiant ML370 or 5500 using a SMART Array Controller?

NOTE:     The Compaq EFS 5.34 readme.txt files contains more information
          on installing SCO OpenServer.  In section 2.6 it mentions a new
          Array Controller driver, known as the 'CLAD':
2.6 Compaq Array Driver (CLAD).

Support is included for the following option cards:

o Compaq Integrated Smart Array Controller o Compaq Smart Array 4200 Controller o Compaq Smart Array 4250 ES Controller o Compaq Smart Array 431 Controller

Solution

Although there may be slight variations in the flow of this procedure based on how you respond to prompts, the process will generally be as follows:

- Boot the server from the SLS OSS604A replacement N1 Boot floppy provided from the SCO ftp site (ftp.sco.com/SLS).

- It will be necessary to have the lastest Compaq EFS. (To obtain the latest Compaq EFS, see ta110210, "How can I obtain the most current Compaq Extended Feature Supplement (EFS) for my SCO operating system?")

- For a first time installation, in response to the Boot: prompt, type "link", as follows:

SCO OpenServer(TM) Release 5
Boot
:defbootstr link=clad hd=Sdsk Srom=wd(0,0,0,0)

Note: The "wd" portion of the line: (0,0,0,0) indicates that the IDE CD-ROM is configured as the master device on the primary IDE controller.

Note: If you have an IDE disk or SATA (Legacy IDE) and SCSI/RAID
disk then OpenServer5 will always try to boot from the IDE disk.
IDE disk controllers have a higher boot priority than a SCSI/raid
controller and OSR507 boot kernel will be preset with the boot HD as
the IDE/SATA one.  Under OSR507, the IDE HD1,2 are static linked in
the kernel (wd), and once the 5.0.7 Kernel gets loaded (even though
it reads it from the SCSI/RAID HD's), the loaded kernel scans the
BIOS and detects the IDE HD (SATA HD) and thinks it will be the boot
Hard disk (trying to mount the /root filesystem from that IDE/SATA
HD), then fails with a 'srmountfun' panic.  This issue should be
overcome with the correct bootstring specifying the correct location
of the SCSI Sdsk to boot from.
Eventually you will see:

Loading kernel symbol table, this may take a few minutes

Please insert the fd(60)clad volume and press <Return>, or 'q' to quit.

- Insert the latest Compaq EFS BTLD diskette and press <Enter>. You will then see:

Insert the Boot Disk and press <Return>

- At this point, insert the replacement SLS OSS604A Boot floppy. You should see something similar to the following in your hardware list, indicating that the contollers were recognized:

%adapter    0x01F0-0x01F7  14  -       type=IDE ctrlr=primary dvr=wd
%adapter    0x2000-0x20FF   5  -       type=clad ha=0 PCI slot=0  (rev 5.34a)
- Eventually you will be prompted to insert the 'clad' BTLD disk.
Insert the BTLD and press <Enter>.  You should see a blue
"RESTRICTED RIGHTS LEGEND" screen.
- Proceed to the "Identifying the installation media device"
screen.  Press the space bar to toggle to SCSI CD-ROM from SCSI
Tape.
Media device to be used: IDE CD ROM
IDE Controller:        primary
Master or Slave:       master

- Insert the CD-ROM media when prompted.

- After entering the licensing information, select the configuration parameters appropriate for your installation.

- To preserve the EISA Configuration Utility (ECU) partition, which we recommend you install prior to installing the operating system, it is necessary to perform an "Interactive fdisk/divvy" installation.

- When prompted for the networking configuration, choose to "defer" networking if you are using the integrated NIC. The driver for the intergated NIC is supplied by the Compaq EFS.

As the system installation proceeds, you may see the following:

Preparing root filesystem ... Done.

The BTLD packages will now be extracted.

Extracting BTLD distribution for clad ... Done.

Extracting additional files from your media source ... Done

Setting files permissions ... Done

- Several additional messages will appear on the screen during the installation process, including the 'Percent Installation Complete'. At approximately 75%, you will receive:

memsize: Invalid checksum
/opt/K/SCO/link/1.1.1Eb/etc/conf/bin/iddeftune: test: argument expected
Press <Enter> to continue:
This message can be safely ignored.
- Eventually, you will see:

Installation and initial configuration of SCO OpenServer Enterprise System is complete.

Before you use the system:

-- Perform any additional configuration needed, as described in the Release Notes.

-- Create an emergency root and boot floppy set as described in the SCO OpenServer Handbook.

(EOF)
Press <Enter> to continue:

- After pressing <Enter>, you will see:

At the "Power Off or Reboot" prompt, remove the floppy disk
from the drive and press any key to reboot.  The screen clears,
then displays the "Boot:" prompt.
Press <Enter> to continue:
**     Safe to Power Off     **
            -or-
**  Press any Key to Reboot  **

- Remove the media and press <Enter>.

- After rebooting the system, proceed to install the Compaq EFS components as per the EFS readme.txt.

From the Xinuos technical article database, record 111072. Reproduced with permission. The original is at www.sco.com/ta/111072, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.