Technical article 105273

I'm having problems installing or using a large EIDE disk drive.

OpenServer 5.0.0OpenServer 5.0.2

Written · Last revised

Problem

When I try to install SCO OpenServer Release 5 on a system that has an EIDE hard drive greater than 2GB, the installation fails when making filesystems with the messages:

Exit value: 1 Status Value: 256 bytes per logical block = 1024 total logical blocks = 2415156 total inodes = 603792 gap (physical blocks) = 1 cylinder size (physical blocks) = 400 setting cluster to default size (16)

Attempting to ignore the above (via the ignore button) results in:

A failure has occurred configuring your hard disks. You may be able to determine the cause of the failure by viewing the error log, then returning to IQM to correct the problem.

Choosing "View Error" here results in:
Starting Hard Disk Initialization ...ERROR: Failed to activate/mount root
About to execute: umount /hdFS/stand
umount: No such file or directory
About to execute: umount -m hdFS
umount: Invalid argument
About to execute: cp /tmp/iqm_file /tmp/iqm_file.fail
About to execute: cp /tmp/iqm_file.imqm /tmp/iqm_file

Solution

SCO OpenServer 5 has problems installing on large EIDE disk
drives.  Follow the steps below to correct the problem:
1. Following the standard installation procedure, boot the system
   from the N00 diskette.  At the boot: prompt, type biosgeom.

2. Either use "customize" and make the root filesystem smaller than 2GB or use "interactive fdisk/divvy".

3. Complete the installation.

4. Reboot from hard disk, use "biosgeom" at the boot: prompt.

5. Go to single-user mode and patch the "wd" driver:

# cd /etc/conf/pack.d/wd
# cp -p Driver.o Driver.o.orig
# _fst -w Driver.o -
* wdsetparam+448?h b6                 [old value: 0xbe]
* wdsetparam+451?h b6                 [old value: 0xbe]
* $q
6. Relink the kernel and reboot.  Do not use "biosgeom" thereafter.
Note that the above offsets are correct for all shipping OpenServer
Release 5 versions of the wd driver, _except_ the original one on
the OpenServer 5.0.0b CD-ROM.  The offsets for that driver are
wdsetparam+440 and +449.  The offsets for the drivers in the
rs500c/ATAPI BTLD, the AHS 5.1 and 5.2 BTLDs, and the 5.0.2c
CD-ROM, are as shown above.
NOTES:    Newer EIDE hard drives larger than 2.6GB are on the market and
          the information above does not apply to these drives.

This procedure will not be necessary for OpenServer releases after SCO OpenServer 5.0.2.

In situations where the primary drive is a small EIDE drive and the problems are with a secondary, larger EIDE drive, patching the wd Driver.o will not affect how the system boots off the original drive.

From the Xinuos technical article database, record 105273. Reproduced with permission. The original is at www.sco.com/ta/105273, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.