Problem
What is needed and what are the steps for installing SCO OpenServer Release 5.0.4 on a Compaq Deskpro 6000?
Solution
The installation of SCO OpenServer 5.0.4 does not require the use
of the Compaq Extended Features Supplement. However, following
successful initial system load, the Compaq EFS will be required
in order to use the Compaq Netelligent Network card.Installation:1. Insert the SCO OpenServer 5.0.4 CD-ROM into CD-ROM unit.
2. Boot off the SCO 5.0.4 Boot Disk.
3. At the <Boot:> prompt, enter:defbootstr disable=ida4. During the boot process a Hardware Configuration Screen will be displayed and among all of the hardware the following will appear:
%tape - - - type=IDE ctlr=pri cfg=slv dvr=Stp -> wd
%cd-rom - - - type=IDE ctlr=pri cfg=slv dvr=Srom -> wdThe tape is not a concern since it will not be part of the kernel after installation (unless a tape unit is connected to the system during installation).
Also, the CD-ROM values are not correct as listed. The actual
configuration of the CD-ROM is Secondary-Master. This setting
cannot be changed at this point, but will be changed later during
the installation.5. Continue with a standard installation up to this screen:
"Identifying the Installation Media Device"The default values listed are:The Media device to be used: IDE CDROM IDE Controller: Primary Master or Slave: Slave
The IDE CD-ROM settings will need to be changed to:
IDE Controller: Secondary
Master or Slave: MasterThe installation will proceed as normal.6. After the installation is complete and the system is rebooted the latest Compaq Extended Features Supplement will need to be added for the Compaq Netelligent Network card.
Note: Before installing the Compaq Extended Feature Supplement, review the Compaq EFS "readme" file for complete information on the installation and removal of the Supplement.
To install the Compaq EFS enter Maintenance Mode (by typing in the root password at the following prompt):
Type CONTROL-d to proceed with normal startup: (or give root password for system maintenance)
7. Insert Volume 1 of the Compaq Extended Feature Supplement. Note that the Compaq EFS can be downloaded from:
ftp.sco.com/EFS/compaq/5.18/(Note: At the time of this article EFS 5.18 was the latest Compaq EFS.)
The files to download are:
--------------------------
VOL.000.000
VOL.001.000
readme8. While in Maintenance Mode type "Custom" to enter the Software
Manager. At this point select "Software" -> "Install New" ->
"From <system_name>" -> "Media Device" -> "Floppy Disk Drive"
-> "Continue" -> "Install".9. During the Compaq EFS installation you will be prompted to enter the network information required to set up the network files.
10. After the Compaq EFS installation, the system will need to be shut down and restarted for the changes to take effect.
NOTES: At the time this article was written, SCO OpenServer 5.0.4 did not have drivers for the Matrox Millennium - II (AGP) Video Card. However, there is a VESA driver that can be used for resolutions above 640x480 and color settings above 16 colors.
The VESA driver can be found at:
ftp.sco.com/pub/drivers/OSR504/graphics/vesa/There will be a VOL.000.00 file which is the driver and a vesa.readme which will contain installation and configuration instructions.
The SCO Release Supplement 504C (rs504c) should be installed _after_ the Compaq EFS has been installed.
The rs504c supplement can be downloaded from:
ftp.sco.com/Supplements/rs504c/The files to download are:
--------------------------
VOL.000.000
VOL.001.000
VOL.002.000
VOL.003.000One of the rs504c.doc files contains the installation information.
See also
TA105732 "Installation of SCO OpenServer 5.0.4 on Compaq Deskpro 4000"
TA105913 "What additional software is required to install SCO operating systems on a Compaq computer?"