Technical article 104715

SCO OpenServer Release 5 is not installing on my SCSI system.

OpenServer 5.0.2OpenServer 5.0.4OpenServer 5.0.5OpenServer 5.0.6

Written · Last revised

Problem

I am installing SCO OpenServer Release 5 on my SCSI system. There are two distinct instances of failure:

1. The installation proceeds for quite some time.  At some
   point, I start to see errors similar to the following:

SCO UNIX System V OS(ver 5.0.0nn) Making component files publicly available Exporting file ...{somefile}

Export phase for "SCO: UNIX" failed Error exporting component SCO:UNIX:5.0.0nn to /{somedir} Error exporting packages of component SCO:UNIX to client... Error exporting package SCO:UNIX:RTS Error exporting file /var/opt/K/SCO/UNIX/... Error creating symbolic link of ... Not a directory

2. The second failure happens when the installation appears
   to complete successfully.  However, when I re-boot the
   system, I see messages similar to the following:

PANIC: srmountfun - Error 22 mountin rootdev hd(1/42) trying to dump nnnn pages to dumpdev hd(1/41) at block 0

Reading from Install: 260 KBSystem Error: 0x5 device transfer read failure

Why is the SCO OpenServer Release 5.0.0 not installing on my SCSI system?

Cause

The installation process for SCO OpenServer Release 5 is
more sensitive to SCSI termination than were previous
releases of the operating system.  The SCSI bus is heavily
loaded during the installation process.  Therefore issues
involving incorrect termination, which were not detectable
in previous releases of the operating system, will prevent
this release of the operating system from installing
correctly.

Termination and SCSI ID assignments, therefore, become critical to the success of the installation.

Solution

The recommended procedure for installation on a SCSI system, when previous attempt(s) at installation have failed, is to do the following, depending on your SCSI configuration:

IF THE INSTALLATION DEVICE AND THE ROOT DEVICE ARE PHYSICALLY LOCATED ON THE INTERNAL BUS:

1.  Remove all devices from the external scsi bus by
    unplugging the cable from the back of the scsi host
    adaptor card (backplane).
2.  Terminate the host adaptor at the backplane.
3.  If the resistor packs are installed on the host adaptor
    card, remove them.
4.  On the internal scsi bus, remove all devices from the
    bus, except the installation device (CD-ROM or tape
    drive) and the root hard disk.  You must remove secondary
    hard drives.  Do not remove the floppy drives.
5.  Ensure that the last physical connection on the internal
    cable is plugged into the terminated device.

(SCO NOTE: It is our experience that hard disk drives provide more reliable termination than do tape or CD-ROM drives.)

IF YOUR INSTALLATION HAS EITHER THE INSTALLATION DEVICE, OR THE ROOT HARD DISK ON THE EXTERNAL BUS, AND THE OTHER DEVICE IS ON THE INTERNAL BUS:

1.  Make sure that the external device has either a passive
    resistor pack plugged into the backplane of the device
    or that the device's termination is activated by setting
    the appropriate switch setting to enable active
    termination.
2.  If the resistor packs are installed on the host adaptor
    card, remove them.
3.  Remove all devices from the internal bus, except
    either the installation device or the root disk
    drive.  You do not need to remove the floppy device(s).
4.  Ensure that the last physical connection on the internal
    cable is plugged into the terminated device.

IF BOTH THE INSTALLATION DEVICE AND THE ROOT HARD DISK ARE LOCATED ON THE EXTERNAL SCSI BUS:

1.  Make sure that the last physical connection of the
    external cable is plugged into the terminated device.

(SCO NOTE: It is our experience that hard disk drives provide more reliable termination than do tape or CD-ROM drives.)

2.  If the resistor packs are *not* installed on the host
    adaptor card, install them.
3.  Remove (unplug) the internal scsi bus cable.

Once this is complete, attempt the installation again. If you still experience problems, re-check your termination. Consider replacing the internal-bus SCSI cable. The passive resistor pack used to terminate the external bus may be defective; consider replacing the passive resistor pack.

NOTE:     The problem symptoms can also occur if Extended BIOS
          Translation for DOS drives > 1 Gb is _Enabled_ through the
          BIOS.  Normally, this setting should be _Disabled_ in the BIOS
          setup for the HBA in order for SCO systems to function
          properly.  However, see TA 105335, "Why does my system
          hang when I install my new Adaptec 2940AU host adapter?",
          for an exception to this rule.

From the Xinuos technical article database, record 104715. Reproduced with permission. The original is at www.sco.com/ta/104715, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.