Technical article 109645

What is SLS OSS486A, the UDK Installation Supplement for SCO OpenServer 5.0.5?

OpenServer 5.0.5

Written · Last revised

Problem

When installing the UnixWare/OpenServer Development Kit on SCO OpenServer 5.0.5, portions of the installation fail.

Solution

Support Level Supplement (SLS) OSS486A provides an installation script that should be run instead of the installation script on the UnixWare/OpenServer Development Kit (UDK) media.

This SLS also provides an updated usoftint package that allows installation of UDK packaging tools and additional UDK libraries on SCO OpenServer 5.0.5.

See the attached cover letter that accompanies this SLS for more information.

See also

ta111009, "How do I install the UnixWare and OpenServer Development Kit (UDK) on my SCO OpenServer Release 5 system?"

Dear SCO Customer,

Support Level Supplement (SLS) OSS486A, the UDK Installation Supplement for OpenServer 5.0.5 allows you to install the UnixWare/OpenServer Development Kit (UDK) on SCO OpenServer 5.0.5.

This SLS is not a custom-installable archive, but rather a compressed tar file containing an installation script to be used instead of the installation script on the UDK media. It also includes updated pkgadd files for the UDK.

Until a version of the UDK media is available, which properly considers SCO OpenServer 5.0.5 and above, use SLS OSS486A to install the UnixWare/OpenServer Development Kit on all SCO OpenServer 5.0.5 systems.

If you have already attempted to install the UDK on SCO OpenServer 5.0.5
without this SLS, use pkgrm to remove all UDK related software and then
use SLS OSS486A to reinstall the desired packages.  See below for more
information.
Software Notes and Recommendations
----------------------------------

SLS OSS486A is intended for use ONLY on these products:

SCO OpenServer Enterprise System Release 5.0.5 SCO OpenServer Desktop System Release 5.0.5 SCO OpenServer Host System Release 5.0.5 UnixWare/OpenServer Development Kit 7.0.0

Failure to use SLS OSS486A to install the UDK will result in:

- <usoftint> module installation failure; - <udkman> module installation failure; - <OSRcompat> module installation failure that corrupts the instance of OSRcompat which installs with the 5.0.5 operating system; - pkginfo -l listing <OSRcompat>'s status as "partially installed."

--------------------------------------------------------------------
IF YOU ALREADY ATTEMPTED TO INSTALL THE UDK ON 5.0.5 WITHOUT OSS486A:
--------------------------------------------------------------------

Before doing anything else, you must follow the directions below in order to reset your system to a state that will be accepted by the installation script provided with SLS OSS486A.

1. Remove the corrupt OSRcompat and other UDK packages.  Check the UDK
   installation status by typing this command:
pkginfo -l

If <OSRcompat> is listed as "partially installed" then you will need to remove it and all other UDK-related packages before using OSS486A. To do this, type:

pkgrm package_names
Select all UDK-related packages that are listed.  The list of UDK
packages is as follows:
baseupd       unmsdk       jdk113
uccs          xdevsys      jdk113pls
ucplus        mtfdev       js10
ustdcomps     BASEman      jws20
OSRcompat     usoftint     udkman

Be careful not to remove any packages that are not a part of the UDK.

*************************************************************************

Note: Do not remove the "UDK Compatibility Module for OpenServer 5.0.5 (ver 5.0.5a)" through Software Manager (custom). Doing so will result in not being able to complete step 2 below.

In the event that this simple mistake is made, please do the following prior to continuing with the steps outlined in this letter:

- Place the OSES 5.0.5 media in the CD-ROM drive. - Mount the CD-ROM:

# mount /dev/cd0 /mnt <return>

- Start Software Manager (custom) and select to install new software, selecting "Media Images" as the Media Device. Enter the following path when prompted for the location of the images and select to Install:

/mnt/opt/patches/SCO:UDKcompat::5.0.5A

- When finished with the re-installation, unmount the OSES 5.0.5 CD-ROM:

#umount /mnt <return>

Remove the media from the drive and continue with the steps outlined in this letter.

*************************************************************************

Follow the prompts until all the UDK packages have been removed. Disregard the dependency checking warnings emitted by pkgrm, as long as the warning only involves items on the list above.

2. Restore the <OSRcompat> package that was installed during the 5.0.5
   operating system installation.  Type:
cd /tmp
zcat /opt/K/SCO/UDKcompat/5.0.5A/UDKcompat/UDKcompat.tar.Z | tar xf -
pkgadd -d /tmp OSRcompat
Note: If this file does not exist on your system you may install the
UDK Compatibility Module for OpenServer 5.0.5 (OSRcompat) from the UDK
CD-ROM.  The version of OSRcompat that is on the UDK CD-ROM will be the
same as, or newer than, the version that was installed with SCO OpenServer
5.0.5.  Insert the UDK CD-ROM in the drive and type:
pkadd -d /dev/cdrom/cdrom1 OSRcompat
Follow the prompts.
I. USING SLS OSS486A
1. Obtain and prepare SLS OSS486A.  Log in as root.

Download the OSS486A file (oss486a.tar.Z). Place the file in the /tmp directory. Uncompress and extract the file by typing these commands:

# cd /tmp
# zcat ./oss486a.tar.Z | tar xvf -
# cd ./oss486a

2. Obtain and mount the UDK CD-ROM.

Place the UDK CD-ROM into the CD-ROM drive and mount it.  For example,
to mount cd0 to /mnt, type:
# mount /dev/cd0 /mnt

3. Run the UDK Installation script, named 505UDKInst.sh, provided with OSS486A, giving the mount-point of the UDK CD-ROM as the argument. For example:

# ./505UDKInst.sh /mnt
You should get the following message:
OSRcompat is already on this system, so will not be
installed.  To force installation of OSRcompat, remove
the current instance on the system and re-run this
script.
Press <Enter> to continue.

4. Press <Enter> and follow the instructions to install the UDK.

II. REMOVING SLS OSS486A
1. You can use "rm" to remove OSS486A.  For example:
rm -rf /tmp/oss486a

2. To remove the UDK, use the pkgrm command.

If you have questions regarding this SLS, or the product on which it is installed, please contact your software supplier.

From the Xinuos technical article database, record 109645. Reproduced with permission. The original is at www.sco.com/ta/109645, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.