Technical article 125837

ad320 version 1.1 drivers for the Adaptec Ultra SCSI 29320/39320 Host Bus Adapters

OpenServer 5.0.6OpenServer 5.0.7

Written · Last revised

Problem

What drivers are available for the Adaptec Ultra320 SCSI Host Adapters?

HARDWARE: Adaptec 39320 PCI Controller Adaptec 39320A PCI Controller Adaptec 29320 PCI Controller Adaptec 29320LP PCI Controller Adaptec 29320ALP PCI Controller Adaptec 29320A PCI Controller AIC-7901A Controller AIC-7901B Controller AIC-7902A4 Controller AIC-7902B Controller

NOTE:     This driver does not support these controllers with the 'HostRAID'
          BIOS option enabled.  This is also known as iROC, or Integrated Raid
          On Chip.

Only the following PCI board IDs are supported:

90058000: ASC-29320A 9005800F: AIC-7901 90058010: ASC-39320 90058011: ASC-39320D 90058012: ASC-29320 90058013: ASC-29320B 90058014: ASC-29320LP 90058015: ASC-39320B 90058016: ASC-39320A 90058017: ASC-29320ALP 9005801C: ASC-39320D 9005801D: AIC-7902B 9005801E: AIC-7901A 9005801F: AIC-7902

When the HostRAID option is enabled in the BIOS, the PCI board ID for any of the above controllers changes to one in the range of 90058080-9005809F.

A PCI board ID in this range, indicates that the HostRAID option
is enabled and needs to be disabled before the controller will be
recognized by this driver.  Some Adaptec U320 controllers have the
HostRAID feature enabled and don't have a BIOS option to disable it,
and can't be used with this driver.  The ASC-39320 from Dell is one
of the HostRAID-only cards with no BIOS option to disable it.
NOTE:     This driver package is to be installed on:
	  	SCO OpenServer Release 5.0.6a, 5.0.7b
NOTE:     Refer to the ad320(HW) manual page for important information before
          installing this driver.  The manual page is available here:
https://ftp.scoexpert.com/openserver5/507/drivers/ad320_1.1/ad320.HW.html
NOTE:     This driver is also shipped as part of OpenServer 5.0.7
          Supplement CD 3.

Solution

This driver package is available at the following URL:

https://ftp.scoexpert.com/openserver5/507/drivers/ad320_1.1/
Modification History
--------------------
          2003-Aug-01 - Base release
	  2004-Jul-19 - Version 1.1

To install the driver, follow these sets of instructions:

1. Acquire the driver from the ftp address given above.

- Download the btld image to a directory/file on your machine, for example, /tmp/ad320_btld.img.

- Verify the downloaded image using sum:

	           sum -r /tmp/ad320_btld.img
This should return:
57342  2880 /tmp/ad320_btld.img

- Format a floppy media using the format command.

- Copy the downloaded image to the floppy:

	           dd if=/tmp/ad320_btld.img of=/dev/fd0 bs=18k

- Verify the copied floppy image using sum:

	           sum -r /dev/fd0
This should return:
57342  2880 /dev/fd0

- Shutdown the host and install the Adaptec controller.

2a. Fresh Installation on Primary Drive

- Insert a boot disk or Installation CD and boot up the system.

	      - At the boot prompt type:
		    defbootstr link=ad320

- Hit return and continue with normal installation.

	  2b. Secondary Drive Installation
- Boot and Login normally.
	      - Mount the floppy image:
	            mount -r /dev/fd0 /mnt

- Use the BTLD Install script to install the driver:

	            /etc/btldinstall /mnt

Once the kernel has been relinked reboot the host and verify that the driver is initializing the card. The boot time banner should look similar to:

%adapter      0xec00-0xecff  11   -   type=ad320 ha=0 slot=0 bus=0 id=7 fts=sto
	  If you are installing this machine fresh with no additional operating
          systems or disks configured on the Adaptec Ultra320 adapter, it
          is recommended that you enable "Extended Int 13 Translation for
          DOS Drivers >  1 Gbyte"

This is found in the Adaptec SCSI BIOS configuration Under "Advanced Configuration". If this is not a fresh installation do not enable this option because it will make the contents of existing disks inaccessible.

When the adapter is installed and the boot time banner is properly displayed, you may use the appropriate mkdev script to add a disk, tape, or cdrom to the Ultra SCSI Bus.

Currently this version of the ad320 supports the use of up to two host bus adapters. Dual channel controllers count as two separate adapters.

From the Xinuos technical article database, record 125837. Reproduced with permission. The original is at www.sco.com/ta/125837, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.