Technical article 100097

ARCserve/Open can't find the tape drive on OpenServer 5.0.4 with an ALAD SCSI adapter.

OpenServer 5.0.4

Written · Last revised

Problem

There are many ways to modify the ARCserve configuration.  Please
refer to the SEE ALSO section at the end of this article before
replacing the ALAD driver.  It is possible that modifying the
configuration files will resolve this issue, and replacing the
driver will not be necessary.

After completing an installation of SCO OpenServer Release 5.0.4 and configuring and testing the tape unit with cpio and tar, ARCserve is then installed but fails to find the tape drive. An Adaptec 2940 (7870 chip set) is being used as the SCSI controller for both the boot disk and the tape unit.

The problem can be seen in a number of ways:

I. The /usr/lib/ARCserve/tapesvr.log file may contain errors that look like the following:

Oct-09 14:52:45        E6627 Fail to ioctl SCSI device file: errno=10
                       Device busy
Oct-09 14:52:45        E6909 SCSI Error: Unknown Error

II. Running the astatus command produces a normal output similar to:

tapesvr 548 733 dbserver 543 545 asod 551 aprocess

All of the processes have an appropriate PID, but when the Device Management option is chosen from the ARCserve main menu, the following message is displayed:

Failed to contact ARCserve Tape Server. Please wait for retry.

The error message never clears and ARCserve never contacts the tape.

III. The first time the 'astatus' command is run, the output looks normal (see section II above). However, if the command 'astop' is run and then the command 'astart' is run, the output from the astatus command changes to the following:

tapesvr
dbserver 1111 1112
asod 1119
aprocess

Now the tapesvr process does not show an appropriate PID.

Cause

The problem is caused by the stock ALAD driver that is installed by default when SCO OpenServer 5.0.4 is installed (either via fresh installation or upgrade) on the machine.

Solution

Although OpenServer 5.0.4 installed correctly and everything is
working on the ALAD adapter, the driver will need to be replaced to
enable ARCserve to function.
There is another version of the ALAD driver included on the SCO
OpenServer 5.0.4 CD-ROM.  Follow these steps to install the other
version of the ALAD driver while in single-user mode, where the mount
command refers to the SCO OpenServer 5.0.4 CD-ROM:
mount /dev/cd0 /mnt
cd /etc/conf/pack.d/alad
mv Driver.o Driver.o.orig
mv space.c space.c.orig
cp /mnt/images/alad/Driver.o .
cp /mnt/images/alad/space.c .
cd /etc/conf/cf.d
./link_unix -y
umount /mnt

You will now need to shutdown and restart the system.

After completing the above steps, ARCserve should now work with the tape drive attached to the ALAD adapter.

See also

TA100114, "ARCserve/Open can't contact the tape devices on the system."

TA100081, "Panic when going multiuser on systems with alad driver."

TA105679, "Problems with the alad driver in OpenServer 5.0.4 is causing my system to hang."

From the Xinuos technical article database, record 100097. Reproduced with permission. The original is at www.sco.com/ta/100097, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.