Technical article 127930

Can I export my OpenServer 5 Defintive Virtual Machine from VirtualBox to VMware ESXi?

OpenServer Definitive 2018

Written · Last revised

Problem

I would like to move my OpenServer 5 Definitive Virtual Machine from VirtualBox to VMware ESXi.

Solution

Take the following steps to prepare your VM for export for VMware ESXi.

1) Shutdown and power off the VM in VirtualBox Manager.

2) Create a full clone of the VM and power it up, leaving the original VM powered off.

3) Login to the cloned VM as root

4) Save a copy of the existing kernel, to retain the ability to boot the VM on VirtualBox:

btmnt -w
cp /stand/unix /stand/unix.vbox
btmnt -r

5) Setup a new kernel environment for VMware ESXi with these changes:

5a) Edit /etc/conf/sdevice.d/lsil
        (verify entries set to 'Y')

5b) Edit /etc/conf/sdevice.d/ahci (change all from 'Y' to 'N')

5c) Edit /etc/conf/sdevice.d/wd (change all from 'N' to 'Y')

5d) Edit /etc/conf/cd.d/mscsi Change 'ahci Srom' entry to 'wd Srom 0 0 0 0' Change 'ahci Sdsk' entries to 'lsil Sdsk 0 0 0 0' incrementing the target id so each line is unique.

the results should look similar to:
wd      Srom    0       0       0       0
lsil    Sdsk    0       0       0       0
lsil    Sdsk    0       1       0       0
5e) Build a new kernel:
/etc/conf/cf.d/link_unix -y
6) Shutdown using `shutdown -y -g0`
7) Power down the VM in VirtualBox Manager
8) From VirtualBox Manager, choose  File->Export Appliance

Use 'Open Virtualization Format 1.0' (OVF) file type to create an OVA (Open Virtualization Archive) file. Referenced as MyVM.ova for this article.

NOTE:   The OVA archive is a tar archive with ovf and vmdk files included.

9) Modify the OVF file in the OVA archive.

9a) Use `tar` to extract the OVA archive
    tar xvf MyVM.ova

9b) Edit MyVM.ovf using your preferred editor.

9c) Search for the line: <vssd:VirtualSystemType>virtualbox-2.2</vssd:VirtualSystemType> change it to: <vssd:VirtualSystemType>vmx-07</vssd:VirtualSystemType>

NOTE:   Failure to do step 9c will result in an import error:
        "Unsupported Hardware Family virtualbox-2.2"

9d) Search for the section for the SATA controller, similar to:

<rasd:Caption>sataController0</rasd:Caption>
<rasd:Description>SATA Controller</rasd:Description>
<rasd:ElementName>sataController0</rasd:ElementName>
<rasd:InstanceID>3</rasd:InstanceID>
<rasd:ResourceSubType>AHCI</rasd:ResourceSubType>
<rasd:ResourceType>20</rasd:ResourceType>

Change this to an lsilogic SCSI controller, like this:

<rasd:Caption>scsiController0</rasd:Caption>
<rasd:Description>SCSI Controller</rasd:Description>
<rasd:ElementName>scsiController0</rasd:ElementName>
<rasd:InstanceID>3</rasd:InstanceID>
<rasd:ResourceSubType>lsilogic</rasd:ResourceSubType>
<rasd:ResourceType>6</rasd:ResourceType>
NOTE:    Failure to do step 9d will result in an import error:
         "OVF hardware element 'ResourceType' with instance ID '3'
          No support for the virtual hardware device type '20'"

9e) Remove section for SATA CD-ROM from the ovf file

<Item>
  <rasd:AddressOnParent>1</rasd:AddressOnParent>
  <rasd:AutomaticAllocation>true</rasd:AutomaticAllocation>
  <rasd:Caption>cdrom1</rasd:Caption>
  <rasd:Description>CD-ROM Drive</rasd:Description>
  <rasd:ElementName>cdrom1</rasd:ElementName>
  <rasd:InstanceID>5</rasd:InstanceID>
  <rasd:Parent>3</rasd:Parent>
  <rasd:ResourceType>15</rasd:ResourceType>
</Item>
NOTE:     Failure to do step 9e will result in an import error:
          "No space for ID 5 on Parent 3"

9f) Use tar to recreate MyVM.ova archive file:

tar cvf MyVM.ova MyVM.ovf MyVM-disk001.vmdk MyVM-disk002.vmdk

10) Transfer the modified OVA file to a location where you can import it through your VMware vSphere client.

11) When importing the OVA file into ESXi, the VM should be configured with these characteristics.

Edit the VM settings, check the configuration of these devices:

SCSI LSI Parallel HBA with disks matching IDs set in mscsi. CD-ROM drive as IDE, primary, master [IDE(0:0)] E1000 vNIC

NOTE:     During import you may see an error about OVF conformance or compliance
          check failures.  When prompted, choose 'retry' to relax the OVF
          specification.  The import should continue.
12) Boot the new VM in VMware ESXi. You will see errors
    about a missing network card.  Enter maintenance mode.
13) Run `netconfig`,
13a) Highlight the existing LAN adapter
13b) Choose Hardware->Remove network device
13c) Choose Hardware->Add new LAN adapter

13d) Configure the Intel Pro 1000 for the VMware network

13e) Upon exit, rebuild kernel, shutdown and reboot.

At this point your Virtual Machine migration should be
complete.  If the hostname or IP address changed for the new network,
the system node name, hostname, domain name and gateway may also
need to be updated.  Examine and correct these files:
/etc/default/tcp
/etc/hosts
/etc/resolv.conf

14) Load VMware tools from the OpenServer5 Definitive ISO.

14a) Map the ISO image to the CD-ROM using the vSphere client.

14b) Mount the ISO to the /mnt directory:
     mount /dev/cd0 /mnt

14c) Using the scoadmin software manager (custom), choose: Software->Install New->(this host)->Media Images When prompted for the directory use: /mnt/opt/osr507v Expand the OSR507V for VMware Virtual Machines (ver 3.0) Deselect the main package and select these sub packages:

libdnet - low-level network interface library (ver 3.0.0Ab) pth - GNU Portable Threads (ver 3.0.0Ab) skglib - threaded glib (ver 3.0.0Ab) uriparser - RFC 3986 URI parsing library (ver 3.0.0Ab) vmtools - VMware Tools (ver 3.0.0Ab)

Choose Install

14d) Shutdown and Reboot the VM to start the vmtools.

See also

TA105356 - Can I change my SCSI root controller to another type without reinstalling?

TA127730 - Can my 507v3 virtual machine on VMware be modified to use the E1000 vNIC?

TA110039 - How to change the System Name, Domain Name, and IP address?

TA102428 - Receiving "WARNING: portmapper on server [IP] is not responding" or "WARNING: NLM: RPC call failed: RPC_PMAPFAILURE".

From the Xinuos technical article database, record 127930. Reproduced with permission. The original is at www.sco.com/ta/127930, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.