Technical article 126979

Configuration of SAS Tape Drives on HP ProLiant Servers Configured with HP Smart Array Serial (SAS) Controllers on SCO OpenServer 5.0.7

OpenServer 5.0.7

Written · Last revised

Problem

How to correctly config SAS Tape Drives on HP ProLiant Servers configured with HP Smart Array Serial (SAS) Controllers on SCO OpenServer 5.0.7

HARDWARE: Any HP Proliant Servers
          HP Smart Array SAS E200, E500, P400, P600 & P800
          HP StorageWork Ultrium 448 920 1760 & 1840 SAS Tape
NOTE:     Before you go through the SOLUTION, make sure that the
          HP Smart array SAS Raid controller DOES see the SAS Tape
          from BIOS level.

Solution

First of all, SCO DO NOT recommend installing ANY Tape device on the
same controller which controls the hard disk(s).  It is recommended
to use a separate controller for different speed devices which might
cause bottlenecks on controllers.

If, however, this is not possible then this info was taken from HP Website support knowledge:

To properly configure SAS Tape drives on HP Smart Array Serial Controllers on ProLiant servers running SCO OpenServer 5.0.7, perform the steps outlined in the Details section below. If the SAS Tape drives on HP Smart Array Serial Controllers are not configured as expected, the I/O on tape drives may not be available.

To configure SAS Tape drives on HP Smart Array Serial Controllers, perform the following:

Ensure the "hpsas" is installed in order to use HP Smart Array Serial Controllers. The "hpsas" driver is packaged in the HP ProLiant Extended Feature Supplement for SCO OpenServer 5.

Latest at the time writing this TA, is EFS 5.790a

Please Note: The following dialog is presented when "mkdev tape" is executed. Users are encouraged to respond with the information provided in <ANSWER>.

Run "mkdev tape." This will start Tape Drive Configuration Program.

In the Tape Drive Configuration Program:

1. Configure a SCSI or Enhanced IDE tape drive 2. Configure a different type of tape drive Select an option or enter q to quit: <1>

In the SCSI or Enhanced IDE Tape Drive Configuration Program:

1. Install a SCSI Tape Drive 2. Install an Enhanced IDE Tape Drive 3. Remove a SCSI Tape Drive 4. Remove an Enhanced IDE Tape Drive 5. Change default Tape Drive 6. View Current SCSI and Enhanced IDE Tape Drive configuration

Select an option or enter q to return to main menu: <1>

Enter the prefix of the SCSI host adapter that supports this device Or press the ENTER key for the default: "xxxx"

Enter h for a list of host adapters or enter q to quit: <hpsas>

Which "hpsas" SCSI host adapter supports this device? Select 0 to 29, or enter q to quit: <ha number>

Note: Enter appropriate host adapter number - "0" for the first hpsas host adapter, "1" for the second host adapter, etc.

The Host Adapter parameters will be automatically configured What SCSI Bus is this device attached to? Press the ENTER key to use the default:0 Select 0 through n, or h for help, or q to quit: <4>

Note: Important that you choose the BUS No# 4

What is the Target ID for this device? Select 0 through 15, or h for help, or q to quit : <0>

Note: Target ID is always " 0" for the first tape drive, "1" for the second tape drive, etc.

What is the LUN of this device? Press the ENTER key to use the default: 0 Select 0 through 7, or h for help, or q to quit: <0>

You are about to add the following SCSI device:
Host Adapter Type Adapter Device Number ID LUN Bus
-------------------------------------------------------
SCSI hpsas tape x x 0 4
Update SCSI configuration? (y/n) <Y>

The SCSI configuration file has been updated. Updating system configuration... System files have been successfully updated.

Configuring Tape Driver ...( Stp ) Enter Vendor Identification string or press the ENTER key to use default or enter q to return to main menu: <RETURN for default option>

Enter SCSI version that device is conformant to or press the ENTER key to use default or enter q to return to main menu: <RETURN>

Enter Response Data Format that device uses or Press the ENTER key to use default Or enter q to return to main menu: <RETURN>

The following tape drive types are supported: 1. Generic SCSI-1 / SCSI-2 tape drive 2. EXABYTE 8mm tape drive (8200 or 8500) 3. IBM rebadged EXABYTE 8mm tape drive (8200) 4. DAT drive (Compressing and non-Compressing) 5. QIC Cartridge tape drive

Please choose one of the above, press the ENTER key for default, or enter q to return to main menu: <1>

Tape Driver Successfully Configured Default special devices have been created with the following links: /dev/xct0 linked to /dev/xStp0 /dev/rct0 linked to /dev/rStp0 and /dev/rmt/0b /dev/nrct0 linked to /dev/nrStp0 and /dev/rmt/0bn

In /etc/default/boot: No current boot string. Enter new string, "rm" to remove string, or enter q to leave current string as is: <q>

Then <q> twice to exit the tape configuration manager.

Then answer <Y> three time to relink and use the new kernel and environment.

Reboot the server. The configuration of the tape drive is complete.

Test the access to the tape.
Then generate your emergency BOOT/ROOT floppies "mkdev fd"

See also

TA# 126841 - How to setup and configure a HP StorageWorks Ultrium-2 448 Ultrium-3 920 and Ultrium-4 1760 / 1840 SAS Tape Drive connected to LSI SAS3800X SAS controller on SCO OpenServer 5.0.7 / OpenServer 6.0.0 & UnixWare 7.1.4?

From the Xinuos technical article database, record 126979. Reproduced with permission. The original is at www.sco.com/ta/126979, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.