Technical article 113363

How do I install OpenServer 5.0.4 on an Adaptec 2940U2W with an IDE CD-ROM?

OpenServer 5.0.4

Written · Last revised

Problem

When I install OpenServer 5.0.4 on an Adaptec 2940U2W with an IDE CD-ROM I get the error message "no root controller".

Cause

OpenServer 5.0.4 has no support for the Adaptec 2940U2W.

Solution

If using an AIC-7890 Adaptec chipset (AHA-2940U2W), then "blad325" should be the specified driver.

This driver can be obtained from Adaptec's website at:

http://www.adaptec.com/worldwide/support/supportindex.html

Select the drivers for the "Ultra2 Family."

The driver is a self-extracting executable file which will generate
a Boot Time Loadable Driver (BTLD) disk.  This disk can be mounted
on any OpenServer server with the command:
mount /dev/fd0 /mnt

You will then be able to see in more detail the available drivers.

The latest BIOS for this card is located at the following website:

http://www.adaptec.com/worldwide/common/search.html
Search for "2940U2W bios"

To install using this driver, boot using the OpenServer 5.0.4 boot disk supplied with the operating system.

NOTE: the procedure below applies specifically to a CD-ROM configured
as the "Master" device on the "Primary" IDE controller.  Use the
information outlined below to tailor your installation for other
configurations.

At the boot prompt, enter the following command to use the "blad325" driver supplied by the driver from Adaptec:

Boot
: defbootstr link="blad325" wd.noscan Srom=wd(0,0,0,0)

Please note: You may need to use <Shift> and @ to get quotes if a UK Keyboard is being used.

The "wd.noscan" will prevent the IDE controller from being scanned
for additional hard disks.  If no IDE devices are in use, you may
wish to disable the IDE controller in the BIOS, if applicable, to
release the interrupts 14 and 15.

The "Srom=wd(0,0,0,0)" defines the CD-ROM as being attached to the IDE controller and not the default of being attached to the Adaptec controller.

In this case the (0,0,0,0) stands for the following:

(IDE Controller, Master/Slave, LUN, BUS)

The valid options for "n" are "0 or 1".

IDE Controller:  0 = Primary    1 = Secondary
Master/Slave:    0 = Master     1 = Slave
LUN:             0  (LUN for an EIDE/IDE device is always 0)
BUS:             0  (BUS for an EIDE/IDE device is always 0)

When prompted, insert the driver supplied from Adaptec.

The 2940U2W should then be detected along with the IDE controller and the CD-ROM attached as the master.

NOTES:    Set your IDE CD to "Master" or "Slave".
          The "AUTO-CS" (Cable Select) may not be supported.
In addition, the "blad325" driver allows for some modifiable
parameters in SCO UNIX.  These are detailed below, for reference:
1.    Tag command queuing can be disabled in SCO UNIX by editing the
      file space.c in the directory /etc/conf/pack.d/blad
Change the line:
From:  int blad_do_tagged=1;
To:    int blad_do_tagged=0;
2.    Scatter gathering can be disabled by editing the file space.c
      in the directory /etc/conf/pack.d/blad
Change the line:
From:  int blad_do_sgatter=1;
To:    int blad_do_sgatter=0;
3.    Selection timeout can be changed for the first adapter by
      editing the file /etc/conf/pack.d/blad/space.c
The original line is: aha_change blad_sel_timeout[SCSI_NBLAD];

To force the host adapter to wait 256 ms before reporting a SCSI selection timeout error change this line to:

aha_change blad_sel_timeout[SCSI_NBLAD]={1,BLAD_SEL_256};

To force the host adapter to wait 32 ms before reporting a SCSI selection timeout error change this line to:

aha_change blad_sel_timeout[SCSI_NBLAD]={1,BLAD_SEL_32};

The kernel must be rebuilt for these changes to take effect. Other changeable parameters are documented in the space.c file.

NOTES:     Should the installation hang at "Please wait while your SCSI disks
           are configured into the kernel" then use the bootstring:
:defbootstr scsi.noscan

See also

http://www.adaptec.com/worldwide/support/supporteditorial.html?cat=/Product/AHA-
2940UW&prodkey=SCSI_event_codes

For a list of the SCSI Event Codes that might be received from the controller and their meanings.

ta104918, "I am trying to install an ATAPI/WD CD-ROM as a secondary device."

ta105937, "SCO OpenServer installation bootstring options."

ta109725, "How do I install SCO OpenServer 5.0.4, 5.0.5, or 5.0.6 on a Dell PowerEdge 6300?"

From the Xinuos technical article database, record 113363. Reproduced with permission. The original is at www.sco.com/ta/113363, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.