Problem
How do I install all the necessary components for the HP (Compaq) Insight Manager?
Solution
PLEASE NOTE THAT EFS INSIGHT MANAGEMENT AGENTS HAVE BEEN REMOVED FOR SCO OPENSERVER AS OF 5.770a.
For previous versions, if you available:If you need to install EFS v5.48 or previous on OpenServer 5.0.7, see the NOTES section at the base of this document.
The software detailed below is available from the Foundation Pack provided with the Hardware.
See the accompanying documentation for more information about installation.
1. Install the latest HP (Compaq) Extended Feature Supplement (EFS)
Install by inserting the first EFS disk and running "custom" and loading the software from the floppy media.
You can press RETURN on the HP Extended Feature Supplement and
pick individually, the components you require. This is recommended
as it is not advisable to install drivers and monitors for hardware
you do not have as this runs unnecessary daemons on your server.After installation re-boot your server.If you have installed all the HP Extended Feature drivers you may
wish to disable each monitoring daemon that is not required from
/etc/rc2.d. For example, if the "ciss" host bus adapter is not
present then disable the start-up of the daemon by adding a "exit 0"
to the top of the script.Alternatively, to disable:cled - - - Compaq ProLiant Storage System (rev 5.770a)
cevt - - - hp ProLiant Event Logging Driver (rev 5.770a)
casm 0x2800-0x28ff 10 - hp ProLiant Advanced Server Management DriverEdit the /etc/conf/sdevice.d/casm, cled and cevt and change the second field from "Y" to "N". Save the file and relink the kernel and reboot.
# /etc/conf/cf.d/link_unix -y2. Install the latest HP Insight Manager agents if required.
If you are using the HP Insight Manager CD (Version 5.50) for example, then you will to mount the CD first:
mount -r -olower /dev/cd0 /mntand the software can be found in:
/mnt/agents/sco/eng/compaqcd to each of the agent directories there. There will be four.cmafdtn - Foundation Agent
cmanic - Network Interface Card Agent
cmastor - Storage Agent
cmasvr - Server AgentWithin each directory run the appropriate installation script:
cmafdtn - instfdtn
cmanic - instnic
cmastor - inststor
cmasvr - instsvrDuring the installation of each Agent you will be prompted for:
The System Contact - Written to /etc/snmpd.conf
The System Location - Written to /etc/snmpd.conf
The Community String - default "public"
* The Trap Destination IP - default "0.0.0.0"
The 'reboot' option - default "No"
The 'set' option - default "Yes"After installation it is recommended to re-boot your server.
* The Trap Destination IP can also be set to a Windows 2000 PC
running the Compaq Insight Manager (CIM) software. However,
this PC must have SNMP enable as part of its Network protocol.
To ensure that this is set for Windows 2000, go to:Start | Settings | Control Panel | Network& Dial-up
Connections | Advanced | Optional Network Components |
Management and Monitoring Tools. Once installed from the CD,
it will not be necessary to re-boot your PC.3. If you are using a Compaq UPS then these are also available on the same CD (5.50) in the following:
/mnt/cpqcpm/agents/sco/engThere is an install script and documentation there. The script
can be run with the command:sh ./install.shYou must ensure that the Compaq UPS is connected as the software will try to detect the UPS on the serial port(s) you specify.
Connect the serial cable that came with the UPS from COM1 (Port A)
on the server to the UPS. Make a note of the Part Number of this
serial cable (look at both sides of the D9 connector)Upon a successful detection of the UPS, the software will be installed and the daemon loaded at boot time, however, you still may not see any additional information from the Compaq Insight Manager.
Now Start Compaq Power Management Agent.NOTICE: THERE IS NO NEED TO REBOOT THE SYSTEM, JUST START THE AGENT:
# ./etc/init.d/cpm.init startThis agent will start automatically on boot if server is rebooted by the startup script:
/etc/rc2.d/S99cpminitCheck CIM console because at this stage under Recovery button, UPS button should be active now.
If not, the Compaq Power Management (CPQCPM) Insight plug-in must be installed in the CIM console on the PC.
To do this :a) Close Compaq Insight Manager Console if it is running. b) On the Management CD 5.50 go to directory \cpqcpm\insight\eng and run setup.exe c) Reboot the PC where CIM Console is installed. d) After reboot you will be able to see full details about the UPS
For more information on the types of UPS configuration available see NOTE1.
4. Check the directory /var/spool/compaq for any errors in the log
file(s) there. The Agents are sensitive to the version of "driver"
and "updates" that have been previously installed, above.5. On a PC the Compaq Insight Manager can be installed to monitor activity on the servers where the Agents have been installed.
These are available in two ways; eithera) Using the Web based version : http:<server></server>:2301 and logging on with the user "administrator" and password "administrator".
This feature does not need a Web server to be active on the server.
b) Using the latest Compaq Insight Manager program available from the above Web Site or from the Compaq Insight Manager CD.
If you are running an earlier version of the Compaq Insight Manager
program, you can go into Version Control | Update Database from
CD/diskette to get the information.If you are unable to see the server from the Compaq Insight Manager software and are unable to access the Devices via the Web Agent then see if you are getting the following messages from the file:
/var/spool/compaq/agenterrs.logTIMEOUT: no response response failed Get_response failed read_mem_buf init_snmp_connection
It is likely that the agents are unable to communicate with the Trap
Destination IP address. This is likely to happen if you select the
default of 0.0.0.0. Another IP address to use would be 127.0.0.1.If the server PANIC's upon installation of the Compaq EFS Software, it could be possible that the Compaq Health driver is the cause. The start-up script for this daemon is /etc/rc2.d/S99cmahealth.
Without cmahealth, running the Automatic Server Recovery daemon is
now redundant. The start-up script for this daemon is:/etc/rc2.d/S99cpqasr.This will grade out the "Recovery" icon within the Compaq Insight Manager.
This problem has been reported to SCO Engineering.
- The Compaq Wellness driver may conflict on IRQ 13. If you wish to
see if the driver is conflicting then run the command:hwconfig -hcIf you wish to remove the Compaq Wellness driver then change Y to N in the second field of the following file:
/etc/conf/sdevice.d/cpqwThe kernel will need to be re-linked and this can be done with the command:
/etc/conf/cf.d/link_unix -yThis will grade out the "Expansion Bds" icon within the Compaq Insight Manager.
The following startup scripts in /etc/rc2.d refer to hardware and
services that you may not have on your server. In which case you
may wish not to attempt to start the service each time the server
is turned on. This can be accomplished by simply adding an "exit 0"
statement to the top of the script:S99ciissd See ciissd(CPQEFS) - Compaq IMD Screen IdleThis is the Compaq IMD LCD screen on the front of your server. Running it will display the server's name and date and time on the front LCD panel if there is one present.
S99cmafca See casa(CPQEFS) - Compaq Fibre Controller ArrayS99cmaida See ida(HW) - Compaq Integrated Drive Array ControllerS99cmanic - Compaq Network Interface Card MonitorS99cmascsi - Compaq Fast-SCSI-2 ControllerS99cmasm2 - Compaq Remote Insight Management BoardS99cmaweb - Compaq Insight Management Web ServerS99cpqssd See cpassd(CPQEFS) - Compaq Standby Server daemonS99cpqultra See cpqultra.CPQEFS - Compaq Wide-Ultra SCSI ControllerFurther information on these monitors can be found in:
/usr/spool/compaqNOTE1: When one UPS supports more than one computer and doesn't have a Multiserver Card installed, the configuration is called a UPS group.
If no Multiserver Card is installed and you want to use an UPS Group, only one computer in that UPS group can be attached to the UPS by means of a serial communications cable.
This computer is known as the UPS group controller.
Any computer in the UPS group that is not the UPS group controller is known as a UPS group member.
The UPS group controller will 'talk' directly with the UPS through the serial cable while UPS group members 'talk' with the controller.
If you want change your UPS group configuration, you must reinstall the software.
Below are detailed two worked through examples:
a) WITHOUT MULTISERVER CARD INSTALLED PROCEED WITH THE FOLLOWING ANSWERS:
Is this computer part of a UPS group (y/n) [N]? y
You have specified that this computer is part of a UPS group. Each
UPS group consists of a single group CONTROLLER and one or more group
MEMBERS. The group controller is the computer that is attached to the
communication cable of the UPS. If the computer being installed is
the computer that is attached to the communication cable of the UPS,
select (C)ontroller below.If the computer being installed is NOT attached to the communications cable of the UPS, select (M)ember below.
Is this computer the (C)ontroller or a (M)ember [C]? C IP address to be used in member setup: WWW.XXX.YYY.ZZZ
UPS Group Controller Configuration UPS Group Name: Enter a name (up to 10 characters) for the UPS group that will be controlled by this computer. The group name is used for display purposes only.
Please enter a name for this UPS group[Group Name]: UPS3000
Standard UPS Ports:
1) /dev/tty1A
2) /dev/tty2A
3) Manually enter Device Name.Please enter the UPS port [1]: 1 /dev/tty1A Detecting: Detected UPS 3000 VA FW -0025
Wink Time (seconds):
Users will not be notified of power failures shorter in duration than
the 'Wink Time'. This avoids frequent nuisance warnings for power
failures of short duration.Please enter the Wink Time (1-999 sec.) [5]: 5
Power Failure Countdown Time (minutes): 'Power Failure Countdown Time' specifies how long the system will continue to run on battery before beginning to shutdown the system. During this time, users are alerted each minute of how much time remains until the system will shutdown.
Please enter the Power Failure Countdown Time (1-999 min.) [5]: 5
Time Needed to Down the System (seconds): 'Time Needed to Down the System' is the amount of time needed to complete the system shutdown. For Example: The amount of time required to shutdown all UNIX applications on a server.
Please enter the Time Needed to Shut Down System (1-999 sec.) [180]: 180
Compaq Power Manager Configuration completed successfully.Press <enter> to continue.Installation of Compaq Power Manager for Unix (cpm) was successful.
b) WITH MULTISERVER CARD PROCEED WITH THE FOLLOWING ANSWERS:
Is this computer part of a UPS group (y/n) [N]? n
Standard UPS Ports:
1) /dev/tty1A
2) /dev/tty2A
3) Manually enter Device Name.Please enter the UPS port [1]: 1 /dev/tty1A Detecting: Detected UPS 3000 VA FW -0025
Wink Time (seconds):
Users will not be notified of power failures shorter in duration than
the 'Wink Time'. This avoids frequent nuisance warnings for power
failures of short duration.Please enter the Wink Time (1-999 sec.) [5]: 5
Power Failure Countdown Time (minutes): 'Power Failure Countdown Time' specifies how long the system will continue to run on battery before beginning to shutdown the system. During this time, users are alerted each minute of how much time remains until the system will shutdown.
Please enter the Power Failure Countdown Time (1-999 min.) [5]: 5
Time Needed to Down the System (seconds): 'Time Needed to Down the System' is the amount of time needed to complete the system shutdown. For Example: The amount of time required to shutdown all UNIX applications on a server.
Please enter the Time Needed to Shut Down System (1-999 sec.) [180]: 180
Compaq Power Manager Configuration completed successfully.Press <enter> to continueInstallation of Compaq Power Manager for Unix (cpm) was successful.
NOTE: If the Compaq IDA Monitor is active, it is normal to receive a number
of messages on the system console for 10 times when the server
starts.These messages simply refer to the starting of the disks on the IDA controller and may appear as:
Jun 4 14:24:15 <my_server> CPU4: bp: C3D4CE10
Jun 4 14:24:15 <my_server> CPU3: NOTICE: ida0: slot 6: invalid request on dev 1
36/0 blk 256
Jun 4 14:24:15 <my_server> CPU3: logical unit=0, block=256, size=5, cmd=0xA8,
status=0x10
Jun 4 14:24:15 <my_server> CPU3: Error "invalid request" has been reported 10 t
imes since boot
Jun 4 14:24:15 <my_server> CPU3: Further "invalid request" errors will not
be reported
Jun 4 14:24:15 <my_server> CPU3: CMD_BLK: addr=C0143C7Ch csize=00000094h
Jun 4 14:24:15 <my_server> CPU3: CMD HDR: unit=0 prior=0x00000000 ctrl=0x000000
25
Jun 4 14:24:15 <my_server> CPU3: REQ HDR: next=0 cmd=0x000000A8 ret_code=0x0000
0010
Jun 4 14:24:15 <my_server> CPU3: PARAM: blknum=0x00000100 blkcnt=0x00000005 cnt
=0x00000003 phys addr=0x00095800 virt addr = 0xC0095800 bytes=0x00000400
Jun 4 14:24:15 <my_server> CPU3: bp: C3D4CED8Installing EFS on 507
*********************
If you are trying to install the EFS v5.48 or previous on OpenServer 5.0.7 and
the kernel fails to link, you will need to follow the instructions in:TA125587General EFS and Insight Manager Version Notes
*********************************************
EFS v5.48 was the last EFS to contain the cpqw (Compaq Wellness) driver, needed to monitor older Proliant hardware. It was superseded by the ASM driver.The win32 (legacy) application Compaq Insight Manager (CIM) has been discontinued for some time now.
Although HP recommend that customers migrate from using this win32 program to the newer web version, HP Systems Insight Manager, the win32 release of Insight Manager can still be used for testing purposes. On Windows 2000 and XP systems the only requirement that is needed before CIM (win32) is installed is that snmp is installed in the Windows Control Panel / Add Remove Programs / Add Remove WINDOWS Components / Management and Monitoring Tools. When snmp is installed two services are created, snmp and snmptrap. You should verify that these have started successfully port SNMP installation.When you start the Insight Manager application, select the option, Setup / Winsnmp. Disable the option "Use WinSNMP the next time Insight Manager is started." Now exit Insight Manager and restart it.For the latest HP/Compaq Management Agents please contact your HP Support provider or go to:
http://www.hp.com/cgi-bin/hpsupport/index.pl See also
TA110210, "How can I obtain the most current Compaq Extended Feature Supplement (EFS) for my SCO operating system?"
TA111742, "How can I install the Compaq Insight Manager on Unixware 7?"
TA109248, "How do I disable or enable the Compaq Wellness Driver (cpqw)?"
TA125587, "My kernel relink fails when I try to install the 5.48
version (or previous) of the HP (Compaq) EFS on
OpenServer 5.0.7"