Technical article 111742

How do I install the HP (Compaq) Insight Manager on Unixware7/OpenServer6?

OpenServer 6.0.0UnixWare 7.0.0UnixWare 7.0.1UnixWare 7.1.0UnixWare 7.1.1UnixWare 7.1.2UnixWare 7.1.3UnixWare 7.1.4Open UNIX 8

Written · Last revised

Problem

How do I install all the necessary components for the HP (Compaq) Insight Manager?

Solution

The software detailed below is available at:

http://h18007.www1.hp.com/support/files/server/us/index.html

See the accompanying documentation for more information about installation.

1. Install the latest HP (Compaq) Extended Feature Supplement "Drivers" (EFS) - HBA Disk, relevant to your Compaq hardware.

Please note: The latest drivers might not support the hardware you have.

After installation, relink the kernel with the command:

cd /etc/conf/bin
./idbuild -B
Reboot your server.

The above packages are the actual drivers for the Compaq Hardware.

2. Install the latest Compaq Extended Feature Supplement "Updates" (EFS) - Update Disks - UTILITIES.

Only install the Updates that are relevant to the drivers you have. For example, do not install the Compaq Fibre Channel Diagnostics (casa) if you are only using the Compaq Smart Array (ida), for example.

The above packages should be the utilities which can be used to interact with the Compaq HBA Drivers, above.

3. Install the packages from the Compaq Extended Feature Supplement "Updates" (EFS) - Update Disks relevant for the Compaq Insight Management Agents - DAEMONS.

For older versions of the EFS:

You will need to install the Compaq CROM driver (ptfcrom) and the Compaq Health Driver (ptfcpqw) for the Insight Manager agents to run. It is also recommended that you install the EFS documentation.

For later versions of the EFS:

You will need to install the ptfcpqasm and ptfcrid, if the server has a Compaq Remote Insight Lights Out Board (RILO) or built in Insight Lights Out Board (ILO).

Please note: Check the version of the EFS will be compatible with the Compaq Insight Management Agents you intend to install.

After installation, reboot your server.

Please note: For UnixWare 7.0.0 there are some additional "ptfsco" Supplements to install for SNMP.

The above packages are drivers for the Compaq Insight Management Agents which interact with the Compaq HBA Drivers, above.

4. Install the latest Compaq Insight Manager Agents, relevant to your hardware.

- If you are using HP's Platform Support Pack (PSP) then follow the installation instructions provided with this pack.

- If you are using the Compaq Insight Manager CD (Version 5.50) for example, then mount the CD first:

mount -r -F cdfs /dev/cdrom/cdrom1 /CD-ROM_1
The software can be found in:
/CD-ROM_1/agents/uware7/eng/compaq
There is an install script and documentation there.  To run the
script, use the command:
sh ./install

After installation, it is recommended that you reboot your server.

The agents will interact with the Compaq HBA Drivers, through the
Compaq EFS Daemons, above, and will use SNMP traps to report the
status of the hardware, etc back to a central PC.  The IP address of
this PC can be entered when the software is installed, above.

If there is any doubt as to which version to use, then use the version available from the original CD set supplied with the server.

5. If you are using a Compaq UPS, these are also available on the same CD (5.50) in the following:

/CD-ROM_1/cpqcpm/agents/unixware/eng.
There is an install script and documentation there.  To run the
script, use the command:
sh ./install.sh

After installation, it is recommended that you reboot your server.

Please note: to install this product on SCO Open UNIX 8.0.0 it may be necessary to use the "chsysinfo" command as detailed in TA# 114264, "How can I get my UnixWare application to run on Open UNIX 8?"

6. Check the directory /var/spool/compaq for any errors in the log file(s) there.

Please note: The Agents are sensitive to the version of "driver" and "updates" that have been previously installed (above).

7. On a PC, the Compaq Insight Manager can be installed to monitor activity on the servers where the Agents have been installed.

These are available in two ways, either:

a) Using the Web based version:
http://my_server:2301

and logging on with the user "administrator" and password "administrator". A web server does not need to be running.

or:

b) Using the latest Compaq Insight Manager program available from the above Web site or from the Compaq Insight Manager CD.

8. If you do have a Remote Integrate Lights Out (RiLO) (PCI Board) or Integrate Lights Out (iLO) then this can be used as a separate means of checking the integrity of the server should there be a problem.

Insert another lead into the NIC provided for the RiLO/iLO Board.

During the Boot process of the server, you should be prompted to press F8 to boot the BIOS of the RiLO/iLO Board.

There you should be able to configure an IP address.

Please note: This should be a unique device on the network. You may also wish to set the password of the Administrator. The initial password should be included on a tag provided with the server. If not, then press F8 when the server boots to configure the RiLO or iLO card, when prompted and Edit the Administrator user and set the password there, or even add a new user.

You can access it then with http://<IP>;
Please note that Graphical displays on the Remote Console will
require a license to be entered.  However, if you don't need
to use a Graphical console then run "scologin disable" and then
UnixWare7 will only display in text and therefore a RiLO/iLO
license will not be required.
NOTES:       Upgrading Your EFS:
             ------------------
             To upgrade from a previous version of EFS then:

1. HBA - Install the new HBA's as normal, first ensuring you have a backup of your server and unix kernel in /stand.

# mount 'marry -a hba' /mnt
# pkgadd -d /mnt <hba>
When finished:
# umount /mnt
# /etc/conf/bin/idbuild -B
Then reboot.
2. The EFS, first remove:
# pkgrm cpqdoc
# pkgrm cpqefs
Then add the latest package with:
# pkgadd -d `pwd`/cpqefs.pkg

and taking care to select the appropriate packages needed only.

When complete, run:
# /etc/conf/bin/idbuild -B
and reboot.
3. The Insight Management Agents with:
# pkgrm cpqsvr
# pkgrm cpqstor
# pkgrm cpqfdtm
# pkgrm cpqdoc
Then install with "./install.sh".
When complete reboot your server.

See also

TA110210, "How can I obtain the most current Compaq Extended Feature Supplement (EFS) for my SCO operating system?"

TA112481, "How do I install the HP (Compaq) Insight Manager on OpenServer?"

TA114264, "How can I get my UnixWare application to run on OpenUNIX 8 (7.1.2)?"

TA109248, "How do I disable or enable the Compaq Wellness Driver
          (cpqw)?"
                                                                                TA125587, "My kernel relink fails when I try to install the 5.48
           version (or previous) of the HP (Compaq) EFS on
           OpenServer 5.0.7"

From the Xinuos technical article database, record 111742. Reproduced with permission. The original is at www.sco.com/ta/111742, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.