Technical article 127543

How to import and run SCO OpenServer 5.0.7V on VMWare Workstation 7 windows edition?

OpenServer 5.0.7

Written · Last revised

Problem

How to import and run SCO OpenServer 5.0.7V release 1.0.0 on VMWare Workstation 7 windows edition?

NOTE:     SCO OpenServer 5.0.7V release 1.0.0 is known to work on VMware
          Workstation 7 but SCO does not officially support it.

Solution

APPLIANCE IMPORT
----------------
Start VMware Workstation 7

From the "File" tab, choose "Import or Export" Click "Next" twice on the Conversion Wizard screens

The conversion wizard take you into three steps.

Step 1: Source Step 2: Destination Step 3: Customization

Step 1:

- Select the type of source you want to use. In our example

Select "Virtual Appliance" and click "Next".

- On the next Conversion Wizard screen, browse the location of the OSR507V OVF file. Click "Next".

- On the next screen, you will see detail information about the SCO OSR5.0.7V appliance. Click "next".

- Accept End User License agreement and then "Next".

In Step2:

- you choose the location of the OSR5.0.7V VM.

- Select "Other Virtual Machine" for the destination type. This will install the OSR5.0.7V VM on the local hard drive of the Windows machine. Then "Next"

- Provide a name for your OSR507V Virtual Machine and the location on disk where it will be stored.

Keep the type of Virtual Machine to create as default for "VMware Workstation" and version "6.5-7.0". Click "Next"

On the next screen, keep the default "Import and convert (full-clone)".

But on the Disk Allocation, choose "Allocate all disk spaces now for better performance".

Optional, you can split the VMDK into 2GB chunk. Click "Next".

- On the next screen, unless you want "NAT" or "Host Only" for VMNetwork, accept the default "VMNetwork Bridged". Click "Next".

In Step 3:

- Just click "Next" on the screen.

- On the next wizard screen, read the summary and if all is OK, click "Finish" to complete.

You can go back and change something before "Finish".

Depending on the spec of your windows machine, the import could take between 10 to 20 minutes.

POST APPLIANCE IMPORT
---------------------

Before you start the OSR5.0.7V rel. 1.0.0, you may need to edit the OSR507V VM and carry out the following:

- Increase the Virtual Machine's Memory Size (default is 256MB), if desired.

Adjust as you feel necessary for your particular OSR 5.0.7 V workload and the sizes of other currently running VMs or VMs to be run concurrently under Workstation 7 for Windows.

- You may need to add a Virtual CD-ROM Drive, as this is missing in the VM. You can either map the Virtual CD-ROM drive to the physical Drive or to an ISO image. When adding the Virtual CD-ROM, make sure you use the CD-ROM device "Advanced settings" to be set to

IDE:   0:0  (primary/master)

This is the CD-ROM device setting already in the osr507v kernel.

- Power on the OSR507V VM and quickly press F2 to enter the VM BIOS. The OSR507V VM POST BIOS screen is fast and you need to react with pressing F2 quickly.

In the BIOS screen, under "Main" section, under "Primary Master - VMware Virtual ID", enable the "32 bit I/O". This will speed up CD-ROM IO access. Exit and save the changes in VM BIOS.

Now you are ready to power on the SCO OpenServer 5.0.7V on VMware Workstation 7 windows edition.

Power on OSR507V VM and follow the OSr507V boot screen instructions.

NOTE:     At any time while running the OSR5.0.7 VM and you need to
          access a Floppy or CD-ROM drive, you can just select on the
          Workstation 7 Tab:
VM ==> Removable Devices
and attach the CD-ROM or Floppy to a file or physical device
as needed.  The device nodes for CD-ROM and floppy are
in the OSr507v kernel.

From the Xinuos technical article database, record 127543. Reproduced with permission. The original is at www.sco.com/ta/127543, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.