Technical article 126363

I Cannot install SCO OpenServer 5.0.7, using a BTLD on a floppy disk via USB floppy drive on a HP Proliant DL380-G4 that has no standard legacy floppy drive attached as default.

OpenServer 5.0.7

Written · Last revised

Problem

I have an HP Proliant DL380-G4 Server that is certified for SCO OpenServer 5.0.7 according on the CHWP.

The DL380-G4 that I have has no standard legacy floppy drive attached to it, since HP now ship their DL380-G4 with no installed legacy floppy drive as default.

I can only attach a USB floppy drive to it. In order for me to install OpenServer 5.0.7 on this server, I need to load the BTLD "ciss" driver from HP EFS 5.70a via USB floppy drive.

When installing SCO OpenServer 5.0.7 with sean additional BTLD "ciss", the ISL will need to load the driver twice. First at the initial load of the Install Kernel with the command:

boot
: defbootstr link="ciss"

Second, once the install Kernel has been successfully loaded in the RAM disk with the BTLD, the ISL will then try to access the floppy drive in order to extract the content of the BTLD to the hard drive.

At this stage it fails with an error:

The BTLD package will now be extracted
mount: Bad address
Please select the floppy device you are using
(1) /dev/fd0
(2) /dev/fd1

I have tried the workaround in TA125420, but it did not succeed.

Since the HP DL380-G4 is certified for OpenServer 5.0.7 via HP EFS 5.70a "ciss" BTLD, then how did SCO/HP manage to install OpenServer 5.0.7 successfully on this server?

HARDWARE: HP Proliant DL380-G4

Cause

When you purchase the new DL380-G4 servers, you have the option to have a standard legacy Floppy Driver 1.44 MB installed, or have one without.

HP by default ship the DL380-G4 without a legacy Floppy 1.44 MB Drive. Only a USB Floppy is possible to connect to the DL380-G4.

Since you can have the choice to purchase DL380-G4 with standard legacy Floppy 1.44 MB driver, in the BIOS the Floppy Drive controller is enabled.

In the case of DL380-G4 without a legacy Floppy 1.44 MB Drive (Only USB), OSR507 during first stage of installation in the "defbootstr" routine, detects the USB Floppy Drive and loads the HP BTLD "ciss" driver into the RAM disk. This has nothing yet to do with OSR507 install kernel, but purely done via system BIOS level.

Once the install kernel is loaded, it detects in DL380-G4 BIOS that the standard legacy Floppy Drive is enabled and thus assumes there is a Standard Floppy 1.44 MB Drive attached. So when asked to load the HP BTLD "ciss" again via Floppy disk, the OSr507 install Kernel will try to access the floppy Disk via the Standard Floppy controller, and hence it fails because there is no Floppy Driver on the Floppy controller.

Solution

You need to disable in the BIOS the Standard Floppy Controller, as this is enabled by default.

The BIOS then will use the attached USB Floppy as a legacy Floppy Drive, thus telling the underline OS that there is a legacy Floppy Driver (USB Floppy) and that will be the default to use to access any Floppy 1.44 MB Disk (/dev/fd0 or /dev/fd1 for OSr507).

Once you disable the Standard Floppy Controller in the system BIOS, you will be able successfully load HP BTLD "ciss" via USB floppy drive and install OpenServer 5.0.7.

NOTE:     Ensure you are using the July 2005 cut of OSR507 CD Media which has
          the appropriate USB additions.

See also

TA125420 "I am unable to load a Boot time Loadable driver (BTLD) from a USB floppy drive during ISL (Installation of OSR507).

From the Xinuos technical article database, record 126363. Reproduced with permission. The original is at www.sco.com/ta/126363, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.