Technical article 125420

OSR507:I am unable to load a Boot time Loadable driver (BTLD) from a USB floppy drive during ISL (Installation of OSR507)

OpenServer 5.0.7

Written · Last revised

Problem

When installing SCO OpenServer 5.0.7 with an additional BTLD, the ISL will need to load the driver twice.

First at the initial load of the Install Kernel with the command:

boot
: defbootstr link="BTLD"

Second, once the install Kernel has been successfully loaded in the RAM disk with the BTLD, the ISL will then try to access the floppy drive in order to extract the content of the BTLD to the hard drive.

At this stage it fails with an error:

The BTLD package will now be extracted
mount: Bad address
Please select the floppy device you are using
(1) /dev/fd0
(2) /dev/fd1

HARDWARE: Only systems that do not have a legacy floppy drive. USB is probably more "standard" than legacy by now. Example of such are Notebooks (Laptops), Blade systems & Servers that do not have Legacy Floppy 1.44 MB installed as default.

Cause

The system's BIOS claims that it has one or two legacy
floppy drives, when it does not.  SCO OpenServer 5.0.7 sees
the USB floppy drive as the next floppy drive number after
the legacy floppies claimed by the BIOS.

Solution

NOTE: Please follow the procedure below in order to get OSR5.0.7 installed on a system with USB floppy only.

It will not work with older releases of OpenServer because they do not support USB floppies during ISL.

1- Boot via OpenServer 5.0.7 install CD-1 and at the install boot prompt, enter the following boot string, where <BTLD> is the driver name you are attempting to extract:

boot
: defbootstr Sflp=usb_msto(0,0,0) link="BTLD"

If you are linking multiple BTLDs, use:

boot
: defbootstr Sflp=usb_msto(0,0,0) link="BTLD1 BTLD2"

Note that OSR507 will see the USD floppy diskette as a SCSI disk device. The boot parameter "Sflp" means SCSI-Floppy

usb_msto --> USB driver to use. (0,0,0) ---> USB device ID's. If you had another USB device attached to the server that has a higher order then the USB floppy, then it will look like this: Sflp=usb_msto(0,1,0)

In some servers, you might need to add additional boot parameter if the above fails:

boot
   : defbootstr Sflp=usb_msto(0,0,0) btld=fd(65) link="BTLD"

btld=fd(65) means, load the BTLD from the floppy with minor number 65. Boot loader on the CD is fd(64).

Place the BTLD floppy disk in the USB floppy drive.

2- The install kernel will be loaded and then it requests for the BTLD. After each BTLD is installed, check for error messages indicating that it did not link successfully. If all is well, continue the installation as normal.

The installation will now able to access the USB floppy and extract the BTLD.

NOTES:    It is highly recommend to use the July 2005 cut of OSR507
          CD Media which has the appropriate USB additions and better USB
          driver handling.
NOTES:    Seeing:

FD error: drive=0, block=2, buf addr=618e TIME_OUT : attachment failed to respond

The error occurs right after calling an interuupt routine to jump to the boot rom to read the floppy which might indicate a hardware error of some kind.

From the Xinuos technical article database, record 125420. Reproduced with permission. The original is at www.sco.com/ta/125420, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.