Technical article 127884

Installation issues while installing OpenServer 6

OpenServer 6.0.0

Written · Last revised

Problem

Various problems can arise while installing OpenServer 6, this document will try to document some of those issues and how to address them.

Solution

It is advised that you check our compatibility pages for
your system.  Certified systems have specific notes which
describe the steps used to install the system when it was
certified.
http://www.sco.com/chwp

This article is intended for systems that have not gone through the certification process, where precise instructions are not available.

1) Media needed for installation.

For the installation procedure outlined below, you may need some, or all of the following ISO images burned to CD:

SCO OpenServer6 CD1 (2006-recut ISL CD):
https://ftp.scoexpert.com/openserver6/600/iso/OpenServer-6.0.0-Mar2006/OpenServer-6.0.0Ni-2006-02-08-1513.iso
Special 2012 boot-only CD:
ftp://ftpput.sco.com/tmp/support/ISO/OpenServer-6.0.0Ni-boot-2012-12-04.iso
MP4 CD1 ISO:
https://ftp.scoexpert.com/openserver6/600/mp/osr600mp4/osr600mp4_cd1.iso
OSS711E ISO:
https://ftp.scoexpert.com/openserver6/600/patches/oss711e/oss711e.iso

HBA driver for your disk controller. Which could be covered by one of the following:

https://ftp.scoexpert.com/openserver6/600/drivers/mp4drivers/osr600mp4_drivers.iso
https://ftp.scoexpert.com/openserver6/600/drivers/megasas.20131105/hba.megasas.2013.11.05.iso
https://ftp.scoexpert.com/openserver6/600/drivers/mpt2.20140618/hba.mpt2.2014.06.18.iso

NOTE: Your disk controller vendor may also have an HBA ISO available for download, if your controller is not covered by any of the drivers above.

2) Configuring your system BIOS and hardware, prior to install.

You may need to set your on-board SATA to use a 'Legacy' mode in the BIOS, if available.

SATA CD drives should be connected to SATA port zero.

In some cases, unused features need to be disabled in the BIOS during install.

3) Problems booting the installation media.

Booting from the 2006-recut media may result in some of the following problem scenarios: a) garbled video, characters are unreadable and look squashed. b) may boot initially, but then unable to read any HBAs or continue the installation c) CD not readable or recognition errors.

The special 2012 boot CD contains drivers from MP4 and
OSS711E, which can help.  This Boot-Only CD is just used
for booting, you will be prompted to switch to the ISL CD,
which is the 2006-recut CD.
Some of the features of the 2012 Boot CD are only enabled
by boot parameters.  To enter boot parameters, interrupt
the boot process by hitting the spacebar at the boot:
prompt before the countdown.

These boot parameters are suggested for installation for most systems:

PSM=atup
CONSOLE_VIDEO=VGA
PS2_KEYBOARD=NO

Some systems may also need to change their ACPI settings or disable UDI devices:

UDI_DISABLE=udi
ACPI=N
To continue booting, use the parameter:
boot
4) The ISL - initial system load
One of the first things the ISL will ask for is your HBA
driver CD. Many generic controllers will be supported by
the MP4-HBA CD, while more recent controllers, may need a
special HBA cd.  Check other articles in this database to
find out more about which HBA driver works with your disk
controller.

TA127811 - Host Bus Adapter (HBA) Driver Supplement - megasas Driver version 2013.11.05

TA127857 - Host Bus Adapter (HBA) Driver Supplement - mpt2 Driver version 2014.06.18, IHVVERSION 2014.06.18?

You should see the driver for your HBA listed as it is getting loaded from the media.

After loading your HBA drivers, you'll be prompted to
choose the media device to install from.  Choose to
install from CD-ROM.

At this point, switch to the 2006-recut CD.

When the installation continues, you'll be prompted for information about:

Keyboard License Number System Name, Domain, security, time zone, & Language Hard disk/filesystem setup, optional software Network card, network address, video and graphics, mouse, email root password

After supplying the above information the installation can continue unattended as the hard disk is setup and software is copied to it.

NOTE:     If the driver for your network card is not auto-detected, it
          is better to defer the networking setup and add the driver
          post-ISL.
After this part of the installation is done, DO NOT
REBOOT.  Instead start the software manager (custom) and
install MP4 & OSS711E created from the ISO images from
above. This option is only available to you if you booted from
the special 2012 boot-only CD.
Once MP4 & OSS711E are installed, you can reboot.  Upon
the first reboot, you'll need to still use the boot
parameters:
CONSOLE_VIDEO=VGA
PS2_KEYBOARD=NO

And possibly the ACPI and/or UDI_DISABLE parameters if they were needed previously.

Once booted, added these parameters to the /etc/default/boot file so that they will be used automatically on subsequent boots.

At this point additional patches and software can be
installed and the system can be configured for use.  If
the networking configuration was deferred, put the latest
'nd' driver onto a data CD-R, mount it and install it using
this syntax:
mount /dev/cd0 /mnt
pkgadd -d /mnt nd

Check for the latest 'nd' driver package on the ftp site at:

https://ftp.scoexpert.com/openserver6/600/drivers/

See also

TA126125 - What is patchck?

From the Xinuos technical article database, record 127884. Reproduced with permission. The original is at www.sco.com/ta/127884, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.