Technical article 113601

My server panics with the following error messages "PANIC : ERR : ERROR LOG OVERFLOW" when using Virtual Disk Manager (VDM).

OpenServer 5.0.0OpenServer 5.0.2OpenServer 5.0.4OpenServer 5.0.5OpenServer 5.0.6

Written

Problem

One of the Virtual Disk Manager (VDM) root "pieces" went off line. I booted from the mirrored "root" disk and replaced the faulty drive. When the server was re-booted, VDM re-builds the mirror automatically.

During the build phase, I receive the following error messages and my server panics:

WARNING: VDISK1 HAS BEEN TAKEN OUT OF SERVICE
WARNING: HTFS CAN'T READ SUPERBLOCK ON HTFS VDISK (99/1)
IO FAILURE OCCURRED ACCESSING LOGICAL BLOCK 405481 ON HTFS DEV VDISK
(99/1)

WARNING: ERR: ERROR LOG OVERFLOW PANIC: ERR: ERROR LOG OVERFLOW

Cause

VDM has detected a physical problem with your new hard disk.

Solution

Perform a low level format on the disk (recommended before use with VDM) or replace the disk.

NOTE:     If you have your root disk mirrored on disks on different SCSI
          controllers, ensure that the SCSI BIOS is enabled on both of the
          controllers. If it is not enabled, you will not be able to boot from
          your mirrored disk.  This is controlled by the firmware of your
          controller and not the SCO operating system.
For example, if you were using an Adaptec SCSI controller, press
<Ctrl> A as the server boots and the devices are detected by the
controller.  This will access the Adaptec firmware configuration.

Virtual Disk Manager Release 1.1.0 includes a Release Supplement disk. Before proceeding, make sure it is installed.

SCO OpenServer 5.0.2 and 5.0.4 have the 1.1.0 Supplement included in the product. Release 5.0.0 requires that you install this separately.

It can be downloaded from our FTP site at:

https://ftp.scoexpert.com/Supplements/vdm110

Note: The 1.1.0 Release Supplement, among other things, allows you to mirror your system's boot division (/stand) onto a virtual disk. This will enable you to boot from the mirrored drive should your root disk fail. Again, SCO OpenServer releases 5.0.2 and 5.0.4 already have this included in the product.

See also https://ftp.scoexpert.com/SLS/oss602b

See also

ta104883, "Virtual Disk Manager claims no disk space available for configuration"

ta104939, "How can I mirror or stripe non-root filesystems using Virtual Disk Manager?"

ta105185, "How to mirror my /u filesystem to a second disk using the Virtual Disk Manager."

ta105462, "How do I replace my Raid 5 failed disk and make my online spare a spare again?"

ta105730, "I have mirrored my root disk but cannot boot off the mirrored drive."

ta105734, "How do I configure a MIRROR of Root using the Virtual Disk Manager?"

ta105814, "VDM reports that a disk has bad parity, is offline, or disabled."

From the Xinuos technical article database, record 113601. Reproduced with permission. The original is at www.sco.com/ta/113601, which is reachable but blocked from search engines. Xinuos marks this article against a retired product line. That refers to the product’s lifecycle, not to whether the advice still works — plenty of it still applies to running systems.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.