Technical article 127226

OSR5:What drivers are provided with the OpenServer 5.0.7 media?

OpenServer 5.0.7

Written · Last revised

Problem

How can I find out what drivers are supplied with the SCO OpenServer 5.0.7 media?

Solution

When viewing the CD1 SCO OpenServer 5.0.7 media visit:

\images\boot\readme.htm
for a full listing.
Alternatively see:
SCO OpenServer Release 5.0.7 Installation Diskettes
Contents:

Contents of the images/boot directory The Primary Boot Disk Floppy The Small Memory Boot Disk Floppy The Boot-Time Loadable Drivers (BTLD) Floppies

Creating SCO OpenServer floppy media Creating floppy disks on UNIX systems with ezcp Alternative method for creating floppy disks on UNIX systems Creating floppy disks on Windows systems with ezcp Alternative method for creating floppy disks on Windows systems

-------------------------------------------------------------------------------
Contents of the /images/boot directory

The SCO OpenServer media kit provides both a floppy Boot Disk and the bootable SCO OpenServer System CD-ROM.

In addition, this directory (/images/boot) contains images of all floppy disks you might need. (See ``Creating SCO OpenServer floppy media'' for information on how to create floppy disks from any of these images.)
This directory contains the following files:

install.img: Primary Boot Disk image, which you can use to replace a lost or damaged copy.

install.sum: The 'sum -r' of the primary Boot Disk image.

smallmem.img: An image of a small kernel Boot Disk, for installing on systems with small memory configurations (32MB).

notebook.sum: The 'sum -r' of the small memory Boot Disk image.

btld.img: An image of the first Boot-Time Loadable Drivers (BTLDs) disk, containing drivers for SCSI host adapters, some of which are not supported by the floppy Boot Disk.

btld.sum: The 'sum -r' of the first BTLD image.

btld2.img: An image of the second Boot-Time Loadable Drivers (BTLDs) disk, containing drivers for SCSI host adapters that are not supported by the floppy Boot Disk. There are also some additional BTLDs provided for your convenience.

btld2.sum: The 'sum -r' of the second BTLD image.

The Primary Boot Disk Floppy

This diskette is the one normally used to install SCO OpenServer Release 5.0.7. Your media kit provides a copy of this diskette. If your primary Boot Disk is lost or damaged, however, you can use this image to create another Boot Disk floppy.

Please Note: SCO OpenServer Release 5.0.7 supports bootable CD-ROM installs. If your hardware supports booting from CD-ROM, you do not need to use any floppy diskettes to install SCO OpenServer Release 5.0.7.

The Small Memory Boot Disk Floppy

The small memory Boot Disk floppy should be used to install SCO OpenServer on systems with small memory (32MB) configurations. This kernel has all of the disk drivers removed except for IDE/ATAPI (wd) and Adaptec 1520 (smad). Kernel buffer allocations are also reduced and may affect installation speed.

The Boot-Time Loadable Drivers (BTLD) Floppies

Please Note because SCO OpenServer Release 5.0.6 and earlier systems are unable to uncompress the drivers in the SCO OpenServer Release 5.0.7 BTLD images, you cannot use any of these drivers on pre-Release 5.0.7 systems.

The following lists the SCSI host adapter BTLDs that are provided in the btld.img file. (All of these BTLDs are also available on the SCO OpenServer System CD-ROM).

ad Adaptec 154x, 164x and 174x (in standard mode) ad160 Adaptec 2916x 3916x (7892, 7899 Chip) alad Adaptec 294x 394x 494x (785X 7860 7870 7880 7895 Chip) and SlimSCSI 1480A/B Adapters blad Adaptec 2940U2W 3950U2 (7890, 7891, 7897 Ultra2 Chip) cha Compaq Fast-SCSI-2 Adapter ciss Compaq Intelligent Storage Subsystem clad Compaq Array Controller iir Intel SRCMR, SRCU-31, SRCU-31L, and SRCU-32 Server RAID Controllers mdac Mylex Disk Array Controller slha LSI Logic/Symbios Logic/NCR MPD 53c8xx Host Adapters wd Enhanced IDE, ATAPI Interface

The following lists the BTLDs that are provided in the btld2.img file. (With the exception of the ct driver, all of these BTLDs are also available on the SCO OpenServer System CD-ROM).

ams Advanced Micro Devices PCscsi arad Adaptec 274x, 284x (7770 Chip) blc BusLogic Multi Master Adapters ciha (*) Corollary 386/486 CBUS SCSI-CPU cpqs Compaq EISA SCSI Driver ct Cartridge Tape Driver dptr DPT SCSI & RAID Host Adapters efp (*) Olivetti ESC-1, ESC-2, and EFP Adapters eiad Adaptec 174x (in Enhanced mode) fdhb Adaptec 292x, Future Domain 16x0, 600, 700 (18x0 Chip) flashpt BusLogic FlashPoint Adapters hf IBM HardFile Host Adapters ncr (*) NCR Microchannel Systems Host Adapters piiop (*) Tricord Intelligent I/O Processor smad Adaptec 151x, 152x (6260 & 6360 Chip) & SlimSCSI 1460 Adapters sumo Storage Plus SCSI-AT (SUMO) tmcha (*) Future Domain 845, 850, 860, 885 (950 Chip) wdex (*) Future Domain (formerly Western Digital) 7000EX wdha (*) Future Domain (formerly Western Digital) 7000

*  These drivers are no longer supported by SCO, however they are still provided with SCO OpenServer for your convenience. Contact your hardware vendor for support.
-------------------------------------------------------------------------------
Creating SCO OpenServer floppy media

This section describes how to create a floppy disk from the floppy images provided on the SCO OpenServer CD-ROM, including the floppy Boot Disk, small kernel Boot Disk, and the two BTLD disk images.

To create a floppy disk on an SCO OpenServer system or other UNIX system, see ``Creating floppy disks on UNIX systems using ezcp''.
To create a floppy disk on a Windows or DOS system, see ``Creating floppy disks on Windows systems using ezcp''.
Creating floppy disks on UNIX systems using ezcp

If you are using the first 3.5-inch floppy drive on your system to create an SCO OpenServer floppy disk, we recommend that you use the ezcp command, as described in this section.

Please Note: If you need to use a different drive to create the floppy disk, this procedure will not work. Instead, use the procedure described in ``Alternative method for creating floppy disks on UNIX systems''.

The ezcp command is a UNIX shell script that copies images to /dev/rfd0135ds18. This script is provided on the SCO OpenServer System CD-ROM, in the /images directory.

To create an SCO OpenServer floppy disk on a UNIX system using the ezcp command:

Format a 3.5-inch high density floppy disk using the format(C) command. Label the floppy disk appropriately.

Use the mount(ADM) command to mount the SCO OpenServer System CD-ROM to the /mnt directory or other desired mount point. Change to the /images directory on the SCO OpenServer CD-ROM:

# cd /mnt/images

If you are using a different mount point, substitute it for /mnt in the above example.

Use the ezcp command to copy the desired image to the floppy disk:

ezcp boot/[image_name]

where [image_name] is one of the following image files:

install.img - primary floppy Boot Disk smallmem.img - small kernel Boot Disk btld.img - first Boot-Time Loadable Drivers disk btld2.img - second Boot-Time Loadable Drivers disk

Verify that the image was written to the floppy disk correctly using the sum(C) command:

# sum -r /dev/fd0

Compare the result to the checksum file on the SCO OpenServer CD-ROM (/images/boot/[image_name].sum) that corresponds to the image you copied. If the checksums are the same, the floppy disk is ready for use.

Please Note: Depending on the version of your operating system and the configuration of your hardware, you may use a device node other than /dev/fd0.

Alternative method for creating floppy disks on UNIX systems

If you are unable to use the ezcp command on your UNIX system to create an SCO OpenServer floppy disk because you need to use a drive other than the first 3.5-inch floppy drive, use this approach instead:

Format a 3.5-inch high density floppy disk using the format(C) command. Label the floppy disk appropriately.

Use the mount(ADM) command to mount the SCO OpenServer System CD-ROM to the /mnt directory or other desired mount point.

Change to the /images directory on the SCO OpenServer CD-ROM:

# cd /mnt/images/boot

If you are using a different mount point, substitute it for /mnt in the above example.

Copy the desired image to the floppy disk using the dd(C) command:

# dd if=[image_name] of=/dev/fd0 bs=18k

where [image_name] is one of the following image files:

install.img - primary floppy Boot Disk smallmem.img - small kernel Boot Disk btld.img - first Boot-Time Loadable Drivers disk btld2.img - second Boot-Time Loadable Drivers disk

Verify that the image was written to the floppy disk correctly using the sum(C) command:

# sum -r /dev/fd0

Compare the result to the checksum file on the SCO OpenServer CD-ROM (/images/boot/[image_name].sum) that corresponds to the image you copied. If the checksums are the same, the floppy disk is ready for use.

Please Note: Depending on the version of your operating system and the configuration of your hardware, you may use a device node other than /dev/fd0.

Creating floppy disks on Windows systems using ezcp

If you are using the first 3.5-inch floppy drive on your system to create an SCO OpenServer floppy disk, we recommend that you use the ezcp command, as described in this section.

Please Note: If you need to use a different drive to create the floppy disk, this procedure will not work. Instead, use the procedure described in ``Alternative method for creating floppy disks on Windows systems''.

The ezcp.bat file is a Windows/DOS batch file that uses floppycp to copy floppy images to drive A:. This batch file is provided on the SCO OpenServer System CD-ROM, in the \images directory.

To create an SCO OpenServer floppy disk on a Windows or DOS system using the ezcp command:

Format a 3.5-inch high density floppy disk using the DOS format command. Label the floppy disk appropriately.

Insert the SCO OpenServer System CD-ROM into the CD-ROM drive and change to the \images directory:

D:
cd \images

If your system's CD-ROM drive uses a different drive letter, substitute the correct letter in the above example.

Use the ezcp command to copy the desired image to the floppy disk:

ezcp boot\[image_name]

where [image_name] is one of the following image files:

install.img - primary floppy Boot Disk smallmem.img - small kernel Boot Disk btld.img - first Boot-Time Loadable Drivers disk btld2.img - second Boot-Time Loadable Drivers disk

The floppy disk is now ready for use.

Alternative method for creating floppy disks on Windows systems

If you are unable to use the ezcp command on your Windows or DOS system to create an SCO OpenServer floppy disk because you need to use a drive other than the first 3.5-inch floppy drive, use this approach instead:

Format a 3.5-inch high density floppy disk using the DOS format command. Label the floppy disk appropriately.

Insert the SCO OpenServer System CD-ROM into the CD-ROM drive.

Use the floppycp command to copy the desired image to the floppy disk:

D:\images\floppycp \f D:\images\boot\[image_name]

where [image_name] is one of the following image files:

install.img - primary floppy Boot Disk smallmem.img - small kernel Boot Disk btld.img - first Boot-Time Loadable Drivers disk btld2.img - second Boot-Time Loadable Drivers disk If your system's CD-ROM drive uses a different drive letter, substitute the correct letter in the above example.

For help with the floppycp command, enter:

D:\images\floppycp \h

The floppy disk is now ready for use.

-------------------------------------------------------------------------------
NOTE:  To see the contents of a BTLD floppy disk prior to installation, boot from the boot media, created above, and once booted, insert your BTLD floppy disk then enter:
: dir fd(65)

This will list the contents of the floppy disk.

NOTES:   Below is further information on the some of the drivers:
Adaptec:
=======
Device Drivers
--------------
The 7800 Family Manager Set has two driver files for each operating system; one for Ultra SCSI and earlier devices and one for Ultra2 SCSI devices. This manual refers to both the Ultra SCSI and Ultra2 SCSI drivers when describing installation. Refer to the table below for a list of files for the drivers provided on your installation diskette or CD ROM. Use the columns in the table to determine the correct driver for your SCSI device.
Operating System  UltraSCSI Driver  Ultra2 SCSI Driver
SCO UNIX          alad or alad325   blad or blad325
SCO UnixWare      adsl20 or adsl    adsb20 or adsb

For information on how to install the driver for your SCSI Adapter, refer to the section of this manual describing your specific operating system.

-------------------------------------------------------------------------------
Adaptec 7800 Family Host Adapters
---------------------------------
The following Adaptec PCI-to-SCSI host adapters are collectively referred to as the Adaptec 7800 Family host adapters:
Host Adapter Description
------------------------
AVA-2902I                    PCI-to-Fast SCSI (non-bootable, internal)
AVA-2902E                    PCI-to-Fast SCSI (non-bootable, external)
AVA-2904                     PCI-to-Fast SCSI (non-bootable)
AHA-2910                     PCI-to-Fast SCSI (non-bootable)
AHA-2930                     PCI-to-Fast SCSI
AHA-2940                     PCI-to-Fast SCSI
AHA-2940W                    PCI-to-Fast and Wide SCSI
AHA-2940AU                   PCI-to-Ultra SCSI
AHA-2940U                    PCI-to-Ultra SCSI
AHA-2940UW                   PCI-to-Wide Ultra SCSI
AHA-2940U2W                  PCI-to-Ultra2 Wide Single-ended SCSI
AHA-2940U Dual               MultiChannel PCI-to-Ultra SCSI with Dual External
                             Connectors
AHA-2940UW Dual              MultiChannel PCI-to-Wide Ultra SCSI with Dual
                             External Connectors
AHA-2944W                    PCI-to-Fast and Wide Differential SCSI
AHA-2944UW                   PCI-to-Wide Ultra Differential SCSI
AHA-3940                     MultiChannel PCI-to-Fast SCSI
AHA-3940W                    MultiChannel PCI-to-Fast and Wide SCSI
AHA-3940U                    MultiChannel PCI-to-Ultra SCSI
AHA-3940UW                   MultiChannel PCI-to-Wide Ultra SCSI
AHA-3940UWD                  MultiChannel PCI-to-Wide Ultra SCSI with Dual
                             External Connectors
AHA-3940AU                   MultiChannel PCI-to-Ultra SCSI
AHA-3940AUW                  MultiChannel PCI-to-Wide Ultra SCSI
AHA-3940AUWD                 MultiChannel PCI-to-Wide Ultra SCSI with
                             Dual External Connectors
AHA-3944W                    MultiChannel PCI-to-Fast and Wide
                             Differential SCSI
AHA-3944UWD                  MultiChannel PCI-to-Wide Ultra Differential
                             SCSI with Dual External Connectors
AHA-3944AUWD                 MultiChannel PCI-to-Wide Ultra Differential
                             SCSI with Dual External Connectors
AHA-4944W                    Quad Channel PCI-to-Fast and Wide
                             Differential SCSI
AHA-4944UW                   Quad Channel PCI-to-Ultra Wide Differential SCSI
AIC-7850                     Single-chip PCI-to-Fast SCSI
AIC-7855                     Single-chip PCI-to-Fast SCSI
AIC-7856                     Single-chip PCI-to-Fast SCSI
AIC-7860                     Single-chip PCI-to-Ultra SCSI
AIC-7870                     Single-chip PCI-to-Fast and Wide SCSI
AIC-7880                     Single-chip PCI-to-Wide Ultra SCSI
AIC-7890                     Single-chip PCI-to-Ultra2 SCSI (32 bit)
AIC-7891                     Single-chip PCI-to-Ultra2 SCSI (64 bit)
AIC-7895                     Single-chip PCI-to-MultiChannel Wide Ultra SCSI
AIC-7896                     Single-chip PCI-to-MultiChannel Ultra2 SCSI
                             (32 bit)
AIC-7897                     Single-chip PCI-to-MultiChannel Ultra2 SCSI
                             (32 bit)
NOTES:

The latest drivers for 5.0.7 are available in the Supplemental CD ISO BTLD images from:

http://www.sco.com/support/update/download/release.php?rid=187
Later images may be posted at:
http://www.sco.com/support/downloads.html
TROUBLESHOOTING:

To get the drivers onto a Floppy from Windows then either use the procedure documented in:

https://ftp.scoexpert.com/openserver5/507/iso/osr507suppcd5/osr507suppcd5.html

Alternatively, use Windows freeware RAWWRITE or RAWWRITEWIN to write the:

BTLD1.IMG
or
BTLD2.IMG

to a formatted Windows floppy which will convert it to a SCO Unix Boot Time Loadable Driver (BTLD) diskette.

From the Xinuos technical article database, record 127226. Reproduced with permission. The original is at www.sco.com/ta/127226, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.