Technical article 116592

How do I configure a Compaq network card pair to act as a redundant (failover) pair on OpenServer 5?

OpenServer 5

Written · Last revised

Problem

I have a Compaq dual port NIC card (or two separate NICs), which I want to run as a redundant pair so that if the active one fails, the other can take over giving network card fault tolerance.

This is supported by the software within the Compaq EFS and is not
part of the OpenServer 5 product.  It is specific to Compaq NICs and
cannot be used with other network cards.  SCO Open UNIX 8 and
UnixWare 7 give a more card-generic form of NIC failover redundancy.

Solution

The Compaq EFS for OpenServer 5 should be installed (available from
the Compaq SmartStart CD or from their website).  This software is
installed using the SCOadmin Software Manager.
During installation the EFS will prompt to allow configuration of
any Compaq network cards in the system not currently configured.
This configuration can be done now or can be done later using the
"netconfig" utility.  If configured now, you should select to
configure the cards you wish to run as a redundant pair, add TCP/IP
networking to one of them (entering IP address, netmask and broadcast
as prompted).
When prompted to configure the second Compaq NIC of the redundant
pair choose to configure the card but do not add the TCP/IP
protocol to it. Instead, follow the prompts to have the Compaq NIC
stub driver added.  This will leave the card configured, but with no
protocol on it making it a candidate for a redundant pair binding
with the first NIC.

If this configuration is carried out after installing the EFS, use "netconfig" as usual to add and configure TCP/IP on the first NIC and add the second with the Compaq stub driver on it.

Note: when "netconfig" automatically detects the network cards it
may list the Intel drivers instead of the Compaq drivers, which are
based on Intel's drivers. If you click on the "Configure hardware not
listed above", you should be able to find the Compaq drivers within
the list.  While it is possible to run a Compaq Intel based chipset
NIC with the Intel driver, you can only use the redundant pair
functionality with the Compaq driver.

Once you have one Compaq NIC with TCP/IP configured on it and another with the Compaq NIC stub driver configured within netconfig (and after relinking the kernel and rebooting as prompted) then you can use the Compaq Network Interface Manager "/etc/cpqnim" utility to configure the cards as a redundant NIC pair.

Run "cpqnim" either in the GUI or from a character session and select the option for the model of Compaq NICs that are installed, then take the following steps:

- Highlight the first NIC which was configured with the TCP/IP protocol earlier.

- Select from the menu Configuration -> Bind Redundant Pair

- In the next window, highlight the NIC which was previously configured with the Compaq NIC stub driver and select OK.

The cards should now be linked as a redundant pair (the cpqnim manager will show them with an additional link on the right hand side and one of them marked as "active").

Both NICs should be cabled to the same physical subnet.

NIC failover can be tested by removing the physical network cable
connection from one of the cards.  The driver should detect link
lost from the appropriate card and, if that card was active, then
the redundant card will be marked as "active".  When the link is
restored this is detected but the current active card will remain
active until its link fails.  To restore the original link you must
remove the cable from the redundant card and replace the original
cable.
The redundant cards MAC address is reprogrammed to that of the
primary card as part of this failover so the ARP cache on clients
can remain unchanged.  New connections will be made to the newly
active card and existing connections (telnet session, for example)
will continue without interruption during this failover process.
NOTES:    Cards which support this feature are as follows:

- Compaq Netflex-3/Netelligent (cnet driver) - Compaq Ethernet/FastEthernet (n100c driver) - Compaq Gigabit Controller (n1000c driver)

See also

Compaq EFS documentation.

From the Xinuos technical article database, record 116592. Reproduced with permission. The original is at www.sco.com/ta/116592, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.