Technical article 126868

I cannot access a USB floppy drive to load an HBA driver during system installation.

OpenServer 6.0.0

Written · Last revised

Problem

The server I am installing on does not ship with a floppy drive as part of the configuration. I need to install an additional HBA driver during system installation, but my external USB floppy drive is not recognized.

How can I use a USB Floppy drive at installation time to add additional HBA drivers as part of an OpenServer 6.0.0 install?

Solution

Some servers with a SATA storage controller configured as
the boot controller, and the controller programmed by the
BIOS to be in "Compatible" SATA mode, do not recognize an
external USB floppy drive during the OpenServer 6.0.0
installation process. This TA describes a workaround to
enable the USB floppy drive to be accessible and allow
loading an additional HBA driver(s).

See the Notes section below for possible alternative workarounds.

Procedure:

In order to make the USB floppy accessible, start the SCO OpenServer 6.0.0 installation and do the following:

1. At the ``Load more HBA drivers'' prompt, insert the
   HBA diskette and then press <Alt><SysReq>h to switch
   to the  console text screen to see the enumeration of
   the USB floppy device.  You should see something
   similar to:
VT0>0:0,7,0: HBA           : (usb_msto,1) USB USB HBA
      0,0,0: DISK          : MITSUMI USB FDD 1039

2. To determine the p0 device node that is used to access the USB floppy drive (for example, c0b0t0d0p0 or c1b0t0d0p0), run the following commands:

VT0> cd /dev/dsk
VT0> l *p0
You should see:
brw-rw-rw   1 root  sys   7679,184 Jun 9 13:07 c0b0t0d0p0

3. Verify that this is the correct node for the USB floppy drive by briefly opening the device and noting that the light on the floppy drive flashes and that no error message is displayed:

VT0> < c0b0t0d0p0

4. Rename the USB floppy drive node as a c3 node:

VT0> mv c0b0t0d0p0 c3b0t0d0p0

5. Press <Alt><SysReq><F1> to switch back to the installation.

6. Select "Yes" at the ``Load more HBA drivers'' prompt
   to load the HBA driver(s) from the HBA floppy diskette
   then continue with the rest of the installation.
NOTES:    A fix for this problem will be included in a future
          recut of the OpenServer 6.0.0 installation CD image.
One alternative to using a floppy disk drive to add an
additional HBA driver is to check the SCO Download web
site to determine if the driver is available as a CD
ISO image.  OpenServer 6 provides for the use of HBA
CD-ROM discs during system installation. If an ISO image
is not available, you can transfer the HBA floppy image to
a CD-ROM by following the instructions in SCO technical
article:

TA126675: How can I create a CD iso HBA from a floppy HBA image?

available from http://wdb1.sco.com/kb/search

Another possible alternative is to change the BIOS configuration for the SATA controller to a different mode than "Compatible". Common SATA modes include: "Legacy", "Enhanced", and "AHCI". The BIOS options to change the SATA mode, if provided, vary between OEMs.

From the Xinuos technical article database, record 126868. Reproduced with permission. The original is at www.sco.com/ta/126868, which is reachable but blocked from search engines.

Next step

Need this fixed rather than explained?

Tell us the release, what the system runs and what it is doing. We will reply by email with what we would do next.

  • You deal with the people who do the work
  • No obligation, and no upgrade required before we will help
  • We tell you plainly if something is not worth doing

Send an enquiry

We reply by email. If a server is down, say so in the first line. You can also write to help@scoexpert.com.